Advertisement
Quick Links
TSTATCCPB501
TSTATBBPB501
P474-1050
NOTE: Read the entire instruciton manual before starting the installation.
Form: IM-TSTAT-16
Installation Instructions
I2:00
72
Mo
MULTI-STAGE
Cancels:
HEAT
COOL
74
C
OOL
AUTO
70
H
EAT
HEAT
PUMP
PROGRAMMABLE
Printed in U.S.A.
Digital Thermostat
&
Catalog No. 13TS-TA42
Advertisement
Related Manuals for Carrier TSTATBBPB501
Summary of Contents for Carrier TSTATBBPB501
- Page 1 Installation Instructions TSTATCCPB501 Digital Thermostat TSTATBBPB501 P474-1050 NOTE: Read the entire instruciton manual before starting the installation. HEAT COOL I2:00 & AUTO HEAT PUMP MULTI-STAGE PROGRAMMABLE Catalog No. 13TS-TA42 Form: IM-TSTAT-16 Cancels: Printed in U.S.A.
-
Page 2: Table Of Contents
THE OLD THERMOSTAT AND INSTALLING WARNING THE NEW THERMOSTAT. Replacement Components Division Carrier Corporation 4/01 This device complies with Part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference,... -
Page 3: Preparation
STEP #1 PREPARATION Proper installation of the thermostat will be accomplished by following these step by step instructions. If you are unsure about any of these steps, call a qualified technician for assistance. Assemble tools as shown below. Drill with 3/16 inch Drill Bit (when not using Flat Blade... -
Page 4: Remove Old Thermostat
STEP #2 REMOVE OLD THERMOSTAT Turn off the power to the Heating/Air Conditioning system at the main fuse panel. Most residential systems have a separate breaker for disconnecting power to the furnace. Remove the cover of the old thermostat. If it does not come off easily check for screws. -
Page 5: Install Backplate & Wire
STEP #3 INSTALL BACKPLATE & WIRE Remove the backplate connector from the rear of the thermostat. Install wires as directed below. When finished, snap thermostat on to backplate. If the terminal designations on your old thermostat do not match those on the new thermostat, refer to the chart below, or the wiring diagrams that follow. -
Page 6: Wiring Diagrams
Sample Wiring Diagrams 5 Wire, 1 Stage Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat *, Electric Cool, split systems & package units Thermostat 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return * If using electric heat this option must be selected on during advanced setup. - Page 7 Sample Wiring Diagrams 6 Wire, 2 Stage Cooling, 1 Stage Heat Residential 2 Stage Cooling, with Gas or Electric Heat* Thermostat 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage compressor relay * If using electric heat, this option must be selected during advanced setup.
- Page 8 Sample Wiring Diagrams Commercial Gas or Electric Heat ***, 7 Wire, 2 Stage Cooling, 2 Stage Heat Electric Cool, split systems & package units including Commercial Heat Pumps ** Thermostat 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage compressor relay 2nd stage heat circuit...
-
Page 9: Calibration
Sample Wiring Diagram 6 Wire, 1 Stage Cooling, 2 Stage Heat, Heat Pump * Most residential split and package heat pumps with auxiliary heat Thermostat 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage heat circuit * The heat pump option must be selected on during advanced setup. -
Page 10: Test Operation
STEP #4 TEST OPERATION Turn the power on to the Heating/Air Conditioning system. Press the MODE button repeatedly until the HEAT icon appears on the display. Press the Up or Down buttons until the set temperature is 10 degrees above room temperature. -
Page 11: Troubleshooting
TROUBLESHOOTING SYMPTOM: When using 4 wires (R, G, W, Y), the air conditioning or heat equipment tries repeatedly to turn on, but cannot. At times the display dims or disappears. CAUSE: There is not enough power available to "power share". REMEDY: Connect a 270 ohm, 10 watt power resistor at the furnace as shown below. - Page 12 TROUBLESHOOTING SYMPTOM: The air conditioning does not attempt to turn on. CAUSE: The cooling setpoint is set too high. REMEDY: Consult the Owner's Manual in the Setup section to lower the cooling setpoint limit. SYMPTOM: The heating does not attempt to turn on.
- Page 13 "conventional" (non heat pump) system. REMEDY: Consult the Owner's Manual in the Advanced Setup section to turn off the heat pump. STAR TSTATCCPB501 TSTATBBPB501 P474-1050 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE 4Z95 P/N 88-335 Page 12...