Assembly, Commissioning - Metabo PWE 11-100 Original Instructions Manual

chromium from chemically-treated lumber, hard
wood like oak or beech, Metals, Asbestos.
The risk from these exposures depends on how
long you or bystanders are being exposed.
Do not let particles enter the body.
To reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 10.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
Vacuum or wash the protective clothing Do not
blow, beat or brush
5. Overview
See page 2.
1 Shut-off cock
2 Connection piece
3 Water hose (1/2") with standard self-locking quick
connector
4 Ground Fault Circuit Interrupter (GFCI)
5 TEST button
6 RESET button
7 Pilot light
8 Spindle
9 Additional handle
10 Front protective cap (removable)
11 Spindle locking button
12 Sliding on/off switch
13 Electronic signal indicator
14 Threaded holes on gear housing
15 Thumb screws
16 Locking discs
17 Polishing disc (with velcro-type fastening) *
18 Support plate (with velcro-type fastening) *
19 Speed adjustment wheel
* depending on equipment/not in scope of delivery

6. Assembly, Commissioning

6.1 Fitting of bar auxiliary handle
Always work with the bar auxiliary handle (9)
attached! Fit the bar auxiliary handle as shown
(see illustration A, page 2).
- Fit locking discs (16) to the left and right of the
gear housing.
- Fit the bar auxiliary handle (9) at the gear housing.
- Insert the thumb screws (15) left and right into the
bar auxiliary handle (9) and turn gently.
- Adjust the bar auxiliary handle (9) to the required
angle.
- Firmly tighten the thumb screws (15) to the left and
right manually.
6.2 Power supply
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
The machine must only be connected to a
socket that has been properly earthed in
accordance with regulations.
Regularly check the cable and the plug on the
power tool and have them repaired by the
Metabo after sales service team if damaged.
If an extension cord is needed, it must be a three-
core lead with a protective (earth) contactor that is
properly connected to both the plug and the coupler
of the cord.
When working outdoors, only use the
correspondingly marked extension cable approved
for this purpose.
Regularly check extension cables and replace if
damaged.
Extension cables must be suitable for the power
rating (see Technical Specifications). If using a roll
of cable, always roll up the cable completely.
6.3 Earth leakage circuit breaker (GFCI)
The machine must only be used with the GFCI
(4) supplied.
Check the GFCI (4) as described before each
machine use.
7
6 RESET
5
TEST
4
- Connect the machine to the power supply.
- Push the RESET button (6). The pilot light (7) now
lights up.
- Push the TEST button (5). The pilot light (7)
should go out.
- Press the RESET (6)again to use the machine.
The machine must not be used if you push the
TEST button (5) and the pilot light (7) does not
go out. Have a qualified electrician check the
machine.
Do not use the ground fault circuit interrupter to
switch the machine on or off.
6.4 Shut-off cock
See illustration b, page 2.
Position A = Shut-off cock (1) closed
Position B = Shut-off cock (1) open
ENGLISH en
13