Hitachi P1-00250HFEF Basic Manual page 102

Chapter 4
[oE-35]～[oE-49]
P1-AG Window comparators output condition
Code/Name
oE-35
Window comparator for
[Ai4] higher level
oE-36
Window comparator for
[Ai4] lower level
oE-37
Window comparator for
[Ai4] hysterisis width
oE-38
Window comparator for
[Ai5] higher level
oE-39
Window compareter for
[Ai5] lower level
oE-40
Window compareter for
[Ai5] hysterisis width
oE-41
Window compareter for
[Ai6] higher level
oE-42
Window compareter for
[Ai6] lower level
oE-43
Window compareter for
[Ai6] hysterisis width
oE-44
Operation level at [AI4]
disconnection
oE-45
Operation level
selection at [Ai4] disconnection
oE-46
Operation level at [AI5]
disconnection
oE-47
Operation level
selection at [Ai5] disconnection
oE-48
Operation level at [AI5]
disconnection
oE-49
Operation level
selection at [Ai5] disconnection
・Outputs a signal whenever the analog input value is
within or out of range.
・As for disconnection detection, if it is in the case of
within or out of the range, a value can be set for the
operation command.
Initial
Range (unit)
value
100
-100～100(%)
-100
-100～100(%)
0～10(%) 0
0～100(%) 100
0～100(%) 0
0～10(%) 0
0～100(%) 100
0～100(%) 0
0～10(%) 0
-100～100(%) 0
00(Disable)/
00
01(Out of range)/
02(Inside range)
0～100(%) 0
00(Disable)/
00
01(Out of range)/
02(Inside range)
0～100(%) 0
00(Disable)/
00
01(Out of range)/
02(Inside range)
4-54
For parameter configuration
[oE-50]～[oE-70]
P1-AG Optional analog output adjustment
Code/Name
oE-50
[Ao3] monitor output
selection]
oE-51
[Ao4] monitor output
selection
oE-52
[Ao5] monitor output
selection
oE-56
Filter time constant of [Ao3]
monitor[Ao3] Data type selection
oE-57
[Ao3] Data type selection
oE-58
[Ao3] monitor bias
adjustment
oE-59
[Ao3] monitor gain
adjustment
oE-60
Output level setting at
[Ao3] monitor adjust mode
oE-61
Filter time constant of
[Ao4] monitor
oE-62
[Ao4] Data type selection
oE-63
[Ao4] monitor bias
adjustment
oE-64
[Ao4] monitor gain
adjustment
oE-65
Output level setting at
[Ao4] monitor adjust mode
oE-66
Filter time constant of [Ao5]
monitor
oE-67
[Ao5] Data type selection
oE-68
[Ao5] monitor bias
adjustment
oE-69
[Ao5] monitor gain
adjustment
oE-70
Output level setting at
[Ao5] monitor adjust mode
・Regarding the adjustment method of the analog output,
please refer to the chapter 3 example of I/O terminals
adjustment.
Initial
Range (unit)
value
dA-01
Set monitor code dA-01
dA-01
1～500(ms) 10
00(Absolute value)/
00
01(Signed value)
-100.0～100.0(%) 100.0
-1000.0～1000.0(%) 100.0
0.0～300.0(%) 100.0
1～500(ms) 10
00(Absolute value)/
00
01(Signed value)
-100.0～100.0(%) 100.0
-1000.0～1000.0(%) 100.0
0.0～300.0(%) 100.0
10
1～500(ms)
00(Absolute value)/
00
01(Signed value)
-100.0～100.0(%) 100.0
-1000.0～1000.0(%) 100.0
100.0
0.0～300.0(%)