Advertisement
● 0126: Auto Pan
Cyclically modulates the stereo location of the sound.
No
Parameter
Value
Tri, Sqr, Sin,
1
Mod Wave
0–4
Saw1, Saw2
2
Rate Mode
0–1
Hz, note
3
Rate #1
1–127
0.05–10.00 Hz
4
Rate
0–21
note
5
Depth #2
0–127
0–127
6
Low Gain
0–30
-15–+15 dB
7
High Gain
0–30
-15–+15 dB
8
Level
0–127
0–127
● 012c: Slicer
By applying successive cuts to the sound, this effect turns a conventional sound into a sound that
appears to be played as a backing phrase. This is especially effective when applied to sustain-type
sounds.
No
Parameter
Value
1
Rate Mode
0–1
Hz, note
2
Rate
1–127
0.05–10.00 Hz
3
Rate #1
12–21
note
4
Attack
0–127
0–127
5
Input Sync Sw
0–1
Off, On
Input Sync
6
0–127
0–27
Threshold
7
Mode
0–1
Legato, Slash
8
Shuffle #2
0–127
0–127
9
Level
0–127
0–127
● 0130: Compressor
Flattens out high levels and boosts low levels, smoothing out fluctuations in volume.
No
Parameter
Value
1
Attack #2
0–127
0–127
2
Threshold #1
0–127
0–127
3
Post Gain
0–18
0–+18 dB
4
Low Gain
0–30
-15–+15 dB
5
High Gain
0–30
-15–+15 dB
6
Level
0–127
0–127
Description
Modulation Wave
Tri: triangle wave
Sqr: square wave
Sin: sine wave
Saw1/2: sawtooth wave
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the change (Hz)
Frequency of the change (note)
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
Description
When this is set to "note," the effect is
synchronized with the tempo.
Rate at which the 16-step sequence will
cycle (Hz)
Rate at which the 16-step sequence will
cycle (note)
Speed at which the level changes
between steps
Specifies whether an input note will
cause the sequence to resume from the
first step of the sequence (ON) or not
(OFF)
Volume at which an input note will be
detected
Sets the manner in which the volume
changes as one step progresses to the
next.
Legato: The change in volume from
one step's level to the next remains
unaltered. If the level of a following
step is the same as the one preceding
it, there is no change in volume.
Slash: The level is momentarily set to 0
before progressing to the level of the
next step. This change in volume
occurs even if the level of the following
step is the same as the preceding step.
Timing of volume changes for even-
numbered steps (step 2, step 4, step
6...).
The higher the value, the later the beat
progresses.
Output level
Description
Sets the speed at which compression
starts
Adjusts the volume at which
compression begins
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
● 0131: Limiter
Compresses signals that exceed a specified volume level, preventing distortion from occurring.
No
Parameter
Value
1
Release
0–127
0–127
2
Threshold #1
0–127
0–127
1.5:1, 2:1, 4:1,
3
Ratio #2
0–3
100:1
4
Post Gain
0–18
0–+18 dB
5
Low Gain
0–30
-15–+15 dB
6
High Gain
0–30
-15–+15 dB
7
Level
0–127
0–127
● 0142: Stereo Chorus
This is a stereo chorus. A filter is provided so that you can adjust the timbre of the chorus sound.
No
Parameter
Value
1
Filter Type
0–2
Off, Lpf, Hpf
2
Cutoff Freq
0–16
200–8000 Hz
3
Pre Delay
0–125
0.0–100.0 ms
4
Rate Mode
0–1
Hz, note
5
Rate #1
1–127
0.05–10.00 Hz
6
Rate
0–21
note
7
Depth #2
0–127
0–127
8
Phase
0–90
0–180 deg
9
Low Gain
0–30
-15–+15 dB
10
High Gain
0–30
-15–+15 dB
D100:0W–
11
Balance
0–100
D0:100W
12
Level
0–127
0-–127
● 0140: Hexa Chorus
Uses a six-phase chorus (six layers of chorused sound) to give richness and spatial spread to the
sound.
No
Parameter
Value
1
Pre Delay
0–125
0.0–100.0 ms
2
Rate Mode
0–1
Hz, note
3
Rate #1
1–127
0.05–10.00 Hz
4
Rate
0–21
note
5
Depth #2
0–127
0–127
Pre Delay
6
0–20
0–20
Deviation
Depth
7
0–40
-20–+20
Deviation
8
Pan Deviation
0–20
0–20
D100:0W–
9
Balance
0–100
D0:100W
10
Level
0–127
0–127
MIDI Implementation
Description
Adjusts the time after the signal
volume falls below the Threshold Level
until compression is no longer applied.
Adjusts the volume at which
compression begins
Compression ratio
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
Description
Type of filter
Off: No filter is used
Lpf: Cuts the frequency range above
the Cutoff Freq
Hpf: Cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the chorus sound is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
Description
Adjusts the delay time from the direct
sound until the chorus sound is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Depth of modulation
Adjusts the differences in Pre Delay
between each chorus sound.
Adjusts the difference in modulation
depth between each chorus sound.
Adjusts the difference in stereo
location between each chorus sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be spaced at
60 degree intervals relative to the
center.
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
21
Advertisement
