Advertisement
● Part Parameters
This instrument has 16 parts. Parameters that can be set individually for each Part are called Part parameters.
If you use exclusive messages to set Part parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel). The Block number can be specified as one
of 16 blocks, from 0 (H) to F (H).
The relation between Part number and Block number is as follows.
x...BLOCK NUMBER (0-F),Part 1 (MIDI ch = 1) x = 1
Address (H)
Size (H)
40 1x 00
00 00 02
40 1x 01#
40 1x 02
00 00 01
40 1x 03
00 00 01
40 1x 04
00 00 01
40 1x 05
00 00 01
40 1x 06
00 00 01
40 1x 07
00 00 01
40 1x 08
00 00 01
40 1x 09
00 00 01
40 1x 0A
00 00 01
* When "GM1 System On" and "GM2 System On" are received, Rx. NRPN will be set OFF. When "GS Reset" is received, it will be set ON.
40 1x 0B
00 00 01
40 1x 0C
00 00 01
40 1x 0D
00 00 01
40 1x 0E
00 00 01
40 1x 0F
00 00 01
40 1x 10
00 00 01
40 1x 11
00 00 01
40 1x 12
00 00 01
40 1x 13
00 00 01
40 1x 15
00 00 01
* This parameter sets the Drum Map of the Part used as the Drum Part. This instrument can simultaneously (in different Parts) use up to two Drum Maps (MAP1, MAP2). With the initial settings, Part10 (MIDI
CH = 10, x = 0) is set to MAP1 (1), and other Parts are set to normal instrumental Parts (OFF (0)).
40 1x 16
00 00 01
40 1x 17
00 00 02
40 1x 18#
* PITCH OFFSET FINE allows you to alter, by a specified frequency amount, the pitch at which notes will sound. This parameter differs from the conventional Fine Tuning (RPN #1) parameter in that the
amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are
sounded by means of an identical note number, you can obtain a Celeste effect.
40 1x 19
00 00 01
40 1x 1A
00 00 01
40 1x 1B
00 00 01
40 1x 1C
00 00 01
40 1x 1D
00 00 01
40 1x 1E
00 00 01
40 1x 1F
00 00 01
40 1x 20
00 00 01
40 1x 21
00 00 01
40 1x 22
00 00 01
40 1x 23
00 00 01
* "Rx.BANK SELECT" is set to OFF by "GM1 System On," and Bank Select message will be ignored.
* "Rx.BANK SELECT" is set to ON by "GM2 System On."
* "Rx.BANK SELECT" is set to ON by power-on Reset or by receiving "GS RESET."
Part 2 (MIDI ch = 2) x = 2
:
:
:
Part 9 (MIDI ch = 9) x = 9
Part10 (MIDI ch = 10) x = 0
Part11 (MIDI ch = 11) x = A
Part12 (MIDI ch = 12) x = B
:
:
:
Part16 (MIDI ch = 16) x = F
Data (H)
Parameter
00-7F
TONE NUMBER
00-7F
00-10
Rx. CHANNEL
00-01
Rx. PITCH BEND
00-01
Rx. CH PRESSURE (CAf)
00-01
Rx. PROGRAM CHANGE
00-01
Rx. CONTROL CHANGE
00-01
Rx. POLY PRESSURE (PAf)
00-01
Rx. NOTE MESSAGE
00-01
Rx. RPN
00-01
Rx. NRPN
00-01
Rx. MODULATION
00-01
Rx. VOLUME
00-01
Rx. PANPOT
00-01
Rx. EXPRESSION
00-01
Rx. HOLD1
00-01
Rx. PORTAMENTO
00-01
Rx. SOSTENUTO
00-01
Rx. SOFT
00-01
MONO/POLY MODE
(= CC# 126 01 / CC# 127 00)
00-02
USE FOR RHYTHM PART
28-58
PITCH KEY SHIFT
08-F8
PITCH OFFSET FINE
00-7F
PART LEVEL
(= CC# 7)
00-7F
VELOCITY SENSE DEPTH
00-7F
VELOCITY SENSE OFFSET
00-7F
PART PANPOT
(= CC# 10, except RANDOM)
00-7F
KEY RANGE LOW
00-7F
KEY RANGE HIGH
00-5F
CC1 CONTROLLER NUMBER
00-5F
CC2 CONTROLLER NUMBER
00-7F
CHORUS SEND LEVEL
(= CC# 93)
00-7F
REVERB SEND LEVEL
(= CC# 91)
00-01
Rx. BANK SELECT
Description
CC#00 VALUE 0-127
P.C. VALUE 1-128
1-16, OFF
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
OFF/ON
Mono/Poly
0 = OFF
1 = MAP1
2 = MAP2
-24 - +24 [semitones]
-12.0 - +12.0 [Hz]
Use nibblized data.
0-127
0-127
0-127
-64 (RANDOM),
-63 (LEFT) - +63 (RIGHT)
(C-1)-(G9)
(C-1)-(G9)
0-95
0-95
0-127
0-127
OFF/ON
MIDI Implementation
Default Value (H)
Description
00
0
00
1
Same as the Part Number
01
ON
01
ON
01
ON
01
ON
01
ON
01
ON
01
ON
00 (01*)
OFF (ON*)
01
ON
01
ON
01
ON
01
ON
01
ON
01
ON
01
ON
01
ON
01
Poly
00 at x ≠ 0
OFF at x ≠ 0
MAP1 at x ≠ 0
01 at x = 0
40
0 [semitones]
08 00
0 [Hz]
64
100
40
64
40
64
40
0 (CENTER)
00
C-1
7F
G 9
10
16
11
17
00
0
28
40
01 (00*)
ON (OFF*)
11
Advertisement
