Dolmar ET-71 C Instruction Manual page 8

10. Do not use the tool if the cords are damaged or
worn.
11. Keep extension cord away from cutting elements.
Starting up the tool
1. Make sure that there are no children or other
people within a working range of 15 meters
(50 ft), also pay attention to any animals in the
working vicinity. Otherwise stop using the tool.
2. Before use always check that the tool is safe
for operation. Check the security of the cutting
tool and the guard and the switch trigger/lever
for easy and proper action. Check for clean and
dry handles and test the on/off function of the
switch.
Check damaged parts before further use of
3.
the tool. A guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other condition that may
affect its operation. A guard or other part that
is damaged should be properly repaired or
replaced by our authorized service center unless
indicated elsewhere in this manual.
4. Switch on the motor only when hands and feet
are away from the cutting tool.
Before starting make sure that the cutting tool has
5.
no contact with hard objects such as branches,
stones etc. as the cutting tool will revolve when
starting.
Method of operation
1. Never operate the machine with damaged guards
or without the guards in place.
Only use the tool in good light and visibility.
2.
During the winter season beware of slippery or
wet areas, ice and snow (risk of slipping). Always
ensure a safe footing.
3. Take care against injury to feet and hands from
the cutting tool.
4. Keep hands and feet away from the cutting
means at all times and especially when switching
on the motor.
5. Never cut above waist height.
Never stand on a ladder and run the tool.
6.
7. Never work on unstable surfaces.
8. Do not overreach. Keep the balance at all times.
Always be sure of the footing on slopes. Always
walk and never run.
9. Remove sand, stones, nails etc. found within the
working range. Foreign particles may damage
the cutting tool and can cause to be thrown
away, resulting in a serious injury.
10. Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
8
11. Before commencing cutting, the cutting tool
must have reached full working speed.
12. During operation always hold the tool with both
hands. Never hold the tool with one hand during
use. Always ensure a safe footing.
13. All protective equipment such as guards supplied
with the tool must be used during operation.
14. Except in case of emergency, never drop or
cast the tool to the ground or this may severely
damage the tool.
15. Never drag the tool on the ground when moving
from place to place, the tool may become
damaged if moved in this manner.
16. Always withdraw the mains plug:
− whenever leaving the tool unattended;
− before clearing a blockage;
− before checking, cleaning or working on the
tool;
− before making any adjustments, changing
accessories or storing;
− whenever the tool starts vibrating unusually;
− whenever transporting the tool.
17. Don't force the tool. It will do the job better and
with less likelihood of a risk of injury at the rate
for which it was designed.
Maintenance instructions
1. The condition of the cutting tool, protective
devices and shoulder strap must be checked
before commencing work.
2. Turn off the motor and withdraw the mains plug
before carrying out maintenance, replacing the
cutting tool and cleaning the tool.
3. After use, withdraw the mains plug and check for
damage.
4. Check for loose fasteners and damaged parts
such as nearly halfway cut-off state in the cutting
tool.
5. When not in use store the equipment in a dry
location that is locked up or out of children's
reach.
Use only the manufacturer's recommended
6.
replacement parts and accessories.
7. Always ensure that ventilation openings are kept
clear of debris.
8. Inspect and maintain the tool regularly, especially
before/after use. Have the tool repaired only by
our authorized service center.
9. Keep handles dry, clean and free from oil and
grease.
10. Never use water to cleaning the unit.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure
to follow the safety rules stated in this instruction
manual may cause serious personal injury.