Important Safety Instructions - Dolmar ET-71 C Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
1. This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand
the hazards involved.
2. Children shall not play with the appliance.
3. Be familiar with the controls and proper use of
the equipment.
4. Warning. Cutting elements continue to rotate
after the motor is switched off.
5. Never allow children or people unfamiliar with
the instructions to use the machine.
6. Stop using the machine while people, especially
children, or pets are nearby.
7. Only use the machine in daylight or good artificial
light.
8. Before using the machine and after any impact,
check for signs of wear or damage and repair as
necessary.
9. Take care against injury from any device fitted for
trimming the filament line length. After extending
new cutter line always return the machine to its
normal operating position before switching on.
10. Never replace the non-metallic cutting means
with metallic cutting means.
11. This appliance is not intended for use by
persons (including
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
12. Use the tool with the utmost care and attention.
13. Operate the tool only if you are in good physical
condition. Perform all work calmly and carefully.
Use common sense and keep in mind that the
operator or user is responsible for accidents
or hazards occurring to other people or their
property.
14. Never operate the tool when tired, feeling ill or
under the influence of alcohol or drugs.
15. The tool should be switched off immediately if it
shows any signs of unusual operation.
16. Disconnect the machine from the mains before
checking, cleaning or working on the machine
and when it is not in use.
17. Never use replacement parts or accessories not
provided or recommended by the manufacturer.
Intended use of the tool
1. Use right tool. The electronic grass trimmer is
only intended for cutting grass, light weeds. It
should not be used for any other purpose such
as hedge cutting as this may cause injury.
children) with reduced
Personal protective equipment
1. Dress Properly. The clothing worn should be
functional and appropriate, i.e. it should be tight-
fitting but not cause hindrance. Do not wear
either jewelry or clothing which could become
entangled with high grass. Wear protective hair
covering to contain long hair.
2. When using the tool, always wear sturdy shoes
with a non-slip sole. This protects against injuries
and ensures a good footing.
3. Wear protective glasses or goggles.
Electrical safety
1. Avoid dangerous environment. Don't use the
tool in damp or wet locations or expose it to rain.
Water entering the tool will increase the risk of
electric shock.
2. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
3. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
7. Use of power supply via a RCD with a rated
residual current of 30 mA or less is always
recommended.
8. Before use, check the supply and extension cord for
signs of damage or ageing.
9. If the cord becomes damaged during use, disconnect
the cord from the supply immediately. Do not touch
the cord before disconnecting the supply.
7