Programming - Chamberlain ATS 211X 1/2 HP Owner's Manual

PROGRAMMING

Security✚
The 900 Series remote control works only with door
openers and light controls having an orange "Learn"
button.
Programming instructions are described and illustrated
below. The additional push buttons can also activate
other garage door openers and/or light controls.
(Instructions for programming light products are
included with those accessories.)
Instructions are Described and
Illustrated Below
1. Press and release the "learn"
button on the motor unit. The learn
indicator light will glow steadily for
30 seconds.
2. Within 30 seconds, press and hold
the button on the hand-held
remote.
3. Release the button when the motor
unit light blinks. It has learned the
code. If light bulbs are not
installed, two clicks will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all
codes:
Press and the hold "learn" button on motor unit until the
learn indicator light goes out (approximately 6 seconds).
All previous codes are now erased. Reprogram each
remote or keyless entry you wish to use.
To Control the Opener Lights
®
With Security✚ transmitters, a remote push button can
be programmed to operate the opener lights without
opening the door.
1. With the door closed, press and hold the remote
button that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not
move.
® 3-Channel Remote Control Programming (Optional)
1 2
9 1 9
7 3 7
5
KG
1 2
1 2
KG
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until
completely closed. NEVER permit anyone to cross path of
3
moving gate or door.
1
3
5
KG
Open/Close/Stop Operation
Your Security✚
operate one door using all 3 buttons: the large button
will only open the door, the middle button will close the
door and third button will stop the door's movement.
You may set up this feature as follows:
1. With the door closed, press and
hold the large remote push
button.
2. Press and hold the Lock button
on the door control.
3. Press and hold the door control
push bar.
When the opener lights flash, release all buttons. Test
by pressing the large (Open) button on the remote. The
door should open. Press it again while the door is open
and nothing should happen. Press the middle (Close )
button and the door should close. Press the third
(Stop) button while the door is moving and it should
stop immediately.
The Remote Control Batteries
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The lithium batteries should produce
power for up to 5 years. To replace,
pry open case with visor clip or
screwdriver, as shown. Insert batteries
positive side up (+).
Dispose of old batteries properly.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
26
WARNING
CAUTION
®
remote control can be programmed to
WARNING
CAUTION
Open
Close
Stop