Cub Cadet ZTX6 60 Operator's Manual page 14

Stopping the Engine
1. Disengage the PTO.
2. Move the RH and LH lapbar drive control levers fully outward into the Park
Brake engaged position.
3. Move the throttle control to the FAST position.
4. Turn the key to the STOP position and remove the key from the ignition module.
NOTE: Always remove the key from the ignition module to prevent accidental
starting or battery discharge if the equipment is left unattended.
Practice Operation (Initial Use)
Operating a zero-turn tractor is not like operating a conventional type riding tractor.
Although and because a zero turn tractor is more maneuverable, getting used to
operating the lapbar drive control levers takes some practice.
It is strongly recommended that you locate a reasonably large, level and open
"practice area" where there are no obstructions, pedestrians or animals. You should
practice operating the tractor for a minimum of 30 minutes.
Carefully move (or have moved) the tractor to the practice area. When performing
the practice session, the PTO should not be engaged. While practicing, operate the
tractor at approximately 1⁄2-3⁄4 throttle and at less than full speed in both forward
and reverse.
Carefully practice maneuvering the tractor using the instructions in the following
section Driving the Tractor. Practice until you are confident that you can safely
operate the tractor.
Driving the Tractor
Keep all movement of the lapbar drive control levers slow and smooth.
Abrupt movement of the control levers can affect the stability of the
tractor and could cause the tractor to flip over, which may result in serious
injury or death to the operator.
1. Adjust the operator's seat to the
most comfortable position that
allows you to operate the controls.
See Seat Adjustment in the
Assembly section.
2. Move the RH and LH lapbar drive
control levers inward in the neutral
position which also disengages the
parking brake. Refer to Figure 26.
NOTE: Lapbar drive control levers
must be moved fully inward before
pushing forward or backward to
ensure brakes are fully disengaged.
Parking the tractor on uneven terrain
or a hill may cause the brakes to bind
and not release fully. In this case the
tractor will not drive when the lapbar drive control levers are moved. If this
happens, move the lapbar drive control lever in the opposite direction slightly
to take the load off the brakes and allow them to release fully.
NOTE: If the lapbar drive control levers are not even in the neutral position,
refer to Service and Maintenance for instructions to adjust the lapbar drive
control levers so that they are even.
3. Move the throttle to the full throttle position.
Always maintain a firm grip on the control levers. Do not release the
control levers to slow or stop the tractor; move levers to neutral position
using your hands.
WARNING
Control Levers Moved
Inward & in Neutral
Figure 26
WARNING
OPERATION
4. To drive the tractor, firmly grasp the respective lapbar drive control levers
with your right and left hands and continue with Driving the Tractor Forward
in the next section.
Driving the Tractor Forward
1. Slowly and evenly move
both lapbar drive control
levers forward. The
tractor will start to move
forward. See Figure 27.
2. As the lapbar drive
control levers are
pushed farther forward
the speed of the tractor
will increase.
3. To slow the tractor
move the drive controls
lever rearward to attain
the desired speed, or
move the lapbar drive
control levers to the
neutral position to stop
the tractor.
Turning the Tractor While Driving Forward
Sharp turns can affect control of the tractor. ALWAYS slow the tractor
before making sharp turns.
To turn the tractor while driving forward,
move the lapbar drive control levers as
necessary so that one drive control lever
is rearward of the other. The tractor will
turn in the direction of the rearward
drive control lever.
1. To turn to the left, move the left
drive control lever rearward of
the right drive control lever. See
Figure 28.
2. To turn to the right, move the
right drive control lever rearward
of the left lever. See Figure 29.
3. The greater the distance between
the two levers, the sharper the
tractor will turn.
4. To execute a "pivot turn," move
the turn side drive control
lever to the neutral position
while moving the other control
lever forward.
NOTE: Making a "pivot turn"
on grass will greatly increase
the potential for defacement of
the turf.
14
Driving Forward
Neutral
Position
Figure 27
WARNING
Forward Left Turn
Figure 28
Forward Right Turn
Figure 29
Faster
Slower