Table of Contents
Advertisement
Finish Door Casing Care
Use a glass cleaner and a soft cloth to polish
the casing. Do not use abrasives such as steel
wool, steel pads or an abrasive polish for they
may scratch the casing's finish.
DISPOSING OF ASHES
Whenever ashes get 3 to 4 inches deep in your
firebox, and when the fire has burned down and
cooled, remove excess ashes. Leave an ash bed
approximately 1 inch deep on the firebox bottom
to help maintain a hot charcoal bed.
Remove ashes only when the fire is out and
the ashes are cold (24 to 48 hours after the
fire is out).
Do not leave the ashes in the house as they give
off carbon monoxide and other toxic gases.
WARNING
Disposal of Ashes: Ashes should
be placed in a steel container
with a tight fitting lid and moved
outdoors immediately.
closed container of ashes should
be placed on a non-combustible
floor or on the ground well away
from all combustible materials,
pending final disposal. If the ashes
are disposed of by burial in soil or
otherwise locally dispersed, they
should be retained in the closed
container until all cinders have
thoroughly cooled.
5
3
Figure 3
REFRACTORY REPLACEMENT
The intense heat of the fire will normally cause
hairline cracks in the refractory. These cracks
can be minimized by proper curing as described
in "First Fires". They will not normally dimin-
ish the effectiveness of the refractory. If large
cracks develop, then the refractory should be
replaced. To replace the refractory bricks, fol-
low these steps:
1. Remove the front refractories
2. Remove the bottom refractory
3. Remove the left side refractory
4. Remove the right side refractory
5. Remove the back refractory
6. Remove the front ceramic baffle
7. Remove the rear ceramic baffle
To install the new refractories, follow the above
steps in reverse.
DOOR INSTALLATION
Your fireplaces door has been factory installed
and adjusted.
To remove the door simply unscrew the top
hinge from the door then lift the door (without
touching the trim over the door) to disengage
The
the male part of the bottom hinge from the
female part.
The door adjustment has been set at the factory.
If the fit is still not perfect, you can adjust the
door using the hinge screws.
DOOR ADJUSTMENT
The door may need to be adjusted to be com-
pletely airtight. The gaskets' air-tightness can be
adjusted using the adjustment screw located on
the right side of the fireplace facade (An Allen
key #1/8 – not supplied - will be necessary for
this adjustment).
7
6
4
1
2
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1. Front Refractories
2. Bottom Refractory
3. Left Side Refractory
4. Right Side Refractory
5. Back Refractory
6. Front Ceramic Baffle
7. Rear Ceramic Baffle
Checking Door Seal - A one-inch strip of paper
may be used to perform a test of the integrity
of the door seal. Close the door on the paper
in at least eight points. It is normal to feel only
a slight amount of friction. The door gasket
does not need to be "tight" in all areas, since
a small amount of leakage is not hazardous or
detrimental to the performance of your fireplace.
Figure 4 - Door Installation
Hinges
Adjustment
Gasket Adjustment
Screw
Figure 5
WARNING
• Use only a IHP glass doors,
specifically designed for the
WRT4820WS fireplace.
• The fireplace cannot be oper-
ated without door or firescreen.
Consult your dealer to select
the correct replacement door
or firescreen.
• Important! To assure proper
alignment of glass doors:
Install this fireplace in a
square and plumb condition,
using shims as necessary at
sides and/or bottom.
7
Advertisement
Table of Contents
