Superior Fireplaces WRT6036RS Installation And Operation Instructions Manual
Indoor wood burning fireplace
Hide thumbs
Also See for WRT6036RS:
Table of Contents
Advertisement
Quick Links
P/N 126595-01 Rev. J 10/2019
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 126595-02.
P126595-01
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This wood burning fireplace complies with UL127
CAN/ULC-S610-M87 standard as a FACTORY
BUILT FIREPLACE.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard .
FOR CANADA: The authority having jurisdiction
(such as the municipal building department, fire
department, etc.) should be contacted before
installation to determine the need to obtain a permit.
This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace
system. Please read and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of
the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the
warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation.
IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE
AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.
PFS
C
REPORT NO. F09-095
SAVE THIS BOOK
NOTE: DIAGRAMS AND ILLUSTRATIONS THROUGHOUT THE MANUAL ARE NOT TO SCALE.
Installation and Operation Instructions
Indoor Wood Burning Fireplace
WRT6036RS
WRT6036IS
®
WRT6036RH
US
WRT6036IH
Installateur : Laissez cette notice avec l'appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
Ce foyer au bois est conforme aux UL 127 CAN/ULC-
S610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.
POUR LE CANADA: L'autorité compétente (comme le
service municipal du bâtiment, les pompiers, etc.) doit
être contacté avant l'installation afin de déterminer la
nécessité d'obtenir un permis.
Models
WRT6042RS
WRT6050RS
WRT6042IS
WRT6050IS
WRT6042RH
WRT6050RH
WRT6042IH
WRT6050IH
Advertisement
Table of Contents
Related Manuals for Superior Fireplaces WRT6036RS
Summary of Contents for Superior Fireplaces WRT6036RS
- Page 1 Installation and Operation Instructions Indoor Wood Burning Fireplace Models P/N 126595-01 Rev. J 10/2019 Ce manuel est disponible en francais, simplement en faire la demande. Numéro de la pièce 126595-02. WRT6036RS WRT6042RS WRT6050RS WRT6036IS WRT6042IS WRT6050IS ® WRT6036RH WRT6042RH WRT6050RH...
-
Page 2: Table Of Contents
Thank you for your purchase. We appreciate your business! Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information. Following these safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your fireplace. Please read and understand these instructions before installing or operating. - Page 3 SAFETY Continued WARNING: CONTINUED OVERFIRING CAN PERMA- WARNING: BURNING IMPROPER FUEL (I.E. CHAR- NENTLY DAMAGE YOUR FIREPLACE SYSTEM. SOME COAL) CAN RESULT IN CARBON MONOXIDE POISON- EXAMPLES OF CONDITIONS THAT COULD CAUSE ING, WHICH MAY LEAD TO DEATH! OVERFIRING ARE: Carbon Monoxide Poisoning –...
-
Page 4: Specifications
(267 mm) (242 mm) (178 mm) " 36" (915 mm) " (115 mm) (89 mm) 11" 1" (26 mm) " (1159 mm) (280 mm) " (185 mm) " (388 mm) Figure 1 - 36" WRT6036RS, WRT6036IS, WRT6036RH and WRT6036IH SuperiorFireplaces.us.com 126595-01_J... - Page 5 SPECIFICATIONS Continued 42" MODEL " (775 mm) " (578 mm) " (400 mm) " (670 mm) 29" (737 mm) 23" " (585 mm) (553 mm) (Ref.) " (448 mm) " (32 mm) " (1051 mm) 42" HEARTH " (16 mm) "...
- Page 6 SPECIFICATIONS Continued 50" MODEL " (978 mm) 24" (610 mm) " " (489 mm) (874 mm) " " 23" (724 mm) (553 mm) (585 mm) (Ref.) " (448 mm) " " (1255 mm) (32 mm) 50" HEARTH " (112 mm) 67"...
-
Page 7: Fireplace Installation
FIREPLACE INSTALLATION SELECTING LOCATION 6. Using screws or nails, secure fireplace to framing through flanges located on sides of fireplace. To determine the safest and most efficient location for the fireplace, you must take into consideration the following guidelines: 1. The location must allow for proper clearances (see Figures 4 and 2. - Page 8 FIREPLACE INSTALLATION Continued HEARTH EXTENSION MANTELS A hearth extension projecting a minimum of 20" in front of and a A mantel may be installed if desired (see Figure 7). Woodwork such as minimum of 12" beyond each side of fireplace opening is required wood trims, mantels or any other combustible material projecting from to protect combustible floor construction in front of fireplace.
-
Page 9: Venting Installation
VENTING INSTALLATION LINEAL GAIN OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F) PART NO. DESCRIPTION GAIN The installation of an outside air kit should be performed during Signature Fireplace " (1690 mm) the rough framing of the fireplace due to the nature of it's location. 12-12DM Pipe Section "... - Page 10 VENTING INSTALLATION Continued USING ELBOW OFFSETS (30E-12DM) OFFSET RISE CHIMNEY LENGTH 12" 18" 24" 36" 48" 1. To achieve desired offset, you may install combinations of 12", " " ELBOW SET ONLY 18", 24", 36" and 48" length of double wall pipe (see offset chart "...
- Page 11 VENTING INSTALLATION Continued Return Return Elbow Return Elbow Elbow Offset Offset Elbow Elbow 6' (1.88 m) 6' (1.88 m) Ceiling Max. Max. Support Pipe Return Return 12S-12DM Elbow 6' (1.88 m) Elbow Max. 6' (1.88 m) Offset Offset Max. Elbow Elbow 6' (1.88 m) 6' (1.88 m)
- Page 12 VENTING INSTALLATION Continued FLASHING INSTALLATION (V6F-10DM OR V12F-10DM) 17" Determine the flashing to be used with the roof opening chart. Slide (432 mm) 30" (762 mm) flashing over pipe until base is flat against roof. Replace as many Min. 1" (26 mm) Min.
- Page 13 VENTING INSTALLATION Continued Terminations/Spark Arrestor 10 FOOT RULE The fireplace system must be terminated with the listed round top or All flue gas outlet chimney terminations must extend a minimum of chase terminations. In any case, refer to the installation instructions 3 feet in height above the highest point where it passes through the supplied with the termination.
- Page 14 VENTING INSTALLATION Continued Fabricate a flashing having a 16-1/2" diameter hole centered Termination over chimney end with a 2" collar around hole (see Figure 22). Attach noncombustible spacers at each corner and place flash- Sheet Metal Screw ing over chase. 1"...
- Page 15 VENTING INSTALLATION Continued Attach noncombustible spacers at each corner and place flashing Note: Do Not Seal Termination Cap over chase (see Figure 27). Secure flashing through sides with Ventilation Openings 8-penny nails or sheet rock screws. Caulk Place termination cap over opening. Slip stainless steel inner pipe of termination into inner stainless steel chimney section Storm Collar 6"...
-
Page 16: Firebrick Wall Installation
FIREBRICK WALL INSTALLATION WARNING Slot Right Face LIFTING HAZARD SINGLE -PERSON LIFT COULD CAUSE INJURY. USE ASSISTANCE WHEN MOVING OR LIFTING. FIREBRICK WALL INSTALLATION IMPORTANT: Installation of brick should be done Hearth after the fireplace is placed in a permanent location. Figure 32 - Slots for Firebrick Walls 1. - Page 17 FIREBRICK WALL INSTALLATION Continued GROUTING INSTRUCTIONS INSTALLING SCREEN Material provided: 1. Slide round end of screen rod into rings at top of screen. Attach one push-on nut to end of rod before attaching last ring of screen. Bag of cement 2.
-
Page 18: Optional Gas Line Installation
OPTIONAL GAS LINE INSTALLATION Gas line hook up should be done by your supplier or a qualified Side Outside of service person. Firebrick Fireplace Note: Before you proceed, make sure your gas supply is turned off. Finished Incoming Side Use only a 1/2" black iron pipe and appropriate fittings. 1/2"... -
Page 19: Glass Door Installation
GLASS DOOR INSTALLATION DOOR FRAME MODELS INSTALLING GLASS DOORS Spring clips have been installed but some adjustments may be BDMO36E/G/C, BDMO42E/G/C AND BDMO50E/G/C needed. Install the doors using the following steps: Installation 1. With bifold doors completely folded, insert bottom pivot pin into 1. -
Page 20: Operation And Maintenance Guidelines
OPERATION AND MAINTENANCE GUIDELINES GLASS DOORS Glass doors are optional with the fireplace. When fireplace is in operation, doors must be fully opened or fully closed position only or a fire hazard may be created (see Figure 43). Doors Fully Closed A fireplace equipped with glass doors operates much differently than a Fireplace Front fireplace with an open front. -
Page 21: Technical Service
IMPORTANT NOTICES - CANADA TECHNICAL SERVICE You may have further questions about installation, operation, or IMPORTANT NOTICE troubleshooting. Please contact your IHP dealer for any questions A manufactured shroud which has been approved by a or concerns a. When contacting your dealer please have your model and serial numbers of your fireplace ready. -
Page 22: Parts
PARTS MODELS 36", 42", AND 50" Catalog numbers are included for convenience. MODEL CATALOG NO. WRT6036RS F0600 WRT6036IS F0601 WRT6036RH F0602 WRT6036IH F0603 WRT6042RS F0604 WRT6042IS F0605 WRT6042RH F0606 WRT6042IH F0607 WRT6050RS F0608 WRT6050IS F0609 WRT6050RH F0610 WRT6050IH F0611 16/17 SuperiorFireplaces.us.com... - Page 23 21 of this manual. Catalog numbers are included for convenience. WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved by IHP. Use of non-approved parts can result in poor performance and safety hazards. WRT6036RS (F0600) WRT6042RS (F0604) WRT6050RS (F0608)
- Page 24 PARTS MODELS 36", 42" AND 50" Picture may vary from actual MODEL CATALOG NO. WRT6036RS F0600 WRT6036IS F0601 WRT6036RH F0602 WRT6036IH F0603 WRT6042RS F0604 WRT6042IS F0605 WRT6042RH F0606 WRT6042IH F0607 WRT6050RS F0608 WRT6050IS F0609 WRT6050RH F0610 WRT6050IH F0611 Note: See pages 25 and 26 for part numbers.
- Page 25 PARTS This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on page 21 of this manual. WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved by IHP.
- Page 26 PARTS This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on page 21 of this manual. WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved by IHP.
-
Page 27: Accessories
ACCESSORIES CAT NO. MODEL DESCRIPTION BI-FOLD GLASS DOORS F1011 BDMO36E GLASS DOOR, 36" EBONY F1014 BDMO42E GLASS DOOR, 42" EBONY F1020 BDMO50E GLASS DOOR, 50" EBONY DOUBLE WALL PIPE F0932 12-12DM 12" Section Double Wall Pipe Snap Lock F0933 18-12DM 18"... - Page 28 ACCESSORIES Continued ROOF FLASHING F0942 V6F-10DM Roof Flashing 0 to 6/12 Pitch F0943 V12F-10DM Roof Flashing 6/12 to 12/12 Pitch SQUARE CHASE-TOP TERMINATION F0948 STL-12D Square Top Termination with Slip Section Square Top Termination with Slip Section (Pre-Painted F0949 STL-12DMP Black) ROUND TOP TERMINATIONS F0947...
-
Page 29: Draft Smoke Guidelines
APPENDIX A Draft Requirements take into account all variables within the installation and install the appliance in such a manner that satisfies the draft requirements of Your wood-burning appliance is dependent upon a properly func- the appliance. See Chimney Guidelines to assist you in selecting the tioning chimney for optimum performance. - Page 30 APPENDIX A Continued Smoking – Causes And Troubleshooting Location Recommended To reduce the likelihood of smoking when opening the door, open Marginal Location the combustion air control or damper before opening the door. Wind Direction Your appliance has been designed and tested to provide smoke free Tree operation.
-
Page 31: Warranty
Innovative Hearth Products Superior Brand Wood-Burning Fireplace ® 20 Year Limited Warranty THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior Brand wood burning fireplace ("Product") to be free from defects in materials and ® workmanship at the time of manufacture. The Product body, firebox and ceramic glass carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only. - Page 32 SuperiorFireplaces.us.com Record the following important information about your fireplace: Fireplace model number Fireplace serial number Date fireplace was Installed Dealer name P126595-01 Innovative Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.