Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. See projector enclosure for safety related markings.
The unit should only be repaired by authorized service personnel. Only use attachments/accessories specified by the manufacturer. Do not look into straight into the projector lens during operation. The bright light may harm your eyes. This projector will detect the life of the light source itself. ...
Operation Conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003.
Remote control Power lead Documentation Note: The remote control is shipped with the battery. *(1) For European warranty Information, please visit www.optoma.com. *(2) Available only for Asian region. Optional accessories Lens cap CD user manual*(3) Carry bag...
INTRODUCTION Product Overview Note: Do not block projector intake and exhaust vents. When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake and exhaust vents. Item Item IR Receivers Ventilation (outlet) Keypad Tilt-Adjustment Feet Lens Shift Dial...
INTRODUCTION Keypad Item Item Lamp LED Temp LED Power and Power LED Re-Sync Menu Four Directional Select Keys Keystone Correction Source Enter 10. Information English...
INTRODUCTION Remote control Geometric Correction PIP/PBP Mode AV Mute ENTER Info. Source Re-Sync Volume D Zoom Menu Format Freeze Remote S-Video HDMI1 HDMI2 HDBaseT Video HDMI3 YPbPr DisplayPort Item Item Power on 18. YPbPr (not supported) Geometric Correction 19. Numeric keypad (0-9) Function button (F1) (Assignable) 20.
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the warranty and may shorten the lifetime of the projector light source or the projector itself. For none standard installation advise please contact Optoma. English...
Page 15
SETUP AND INSTALLATION Projector installation notice Notee: Projector power will dim to 70% and fan full load. 195°~345° Portrait mode Air outlet side 10° 10° 10° 10° 10° 10° Allow at least 30 cm clearance around the exhaust vent. Minimum 100mm Minimum 300mm Minimum 300mm...
Page 16
SETUP AND INSTALLATION Minimum 100mm Minimum 100mm (3.94 inches) (3.94 inches) Ensure that the intake vents do not recycle hot air from the exhaust vent. When operating the projector in an enclosed space, ensure that the surrounding air temperature within the enclosure does not exceed operation temperature while the projector is running, and the air intake and exhaust vents are unobstructed.
SETUP AND INSTALLATION Adjusting the projector image Image height The projector is equipped with elevator feet for adjusting the image height. Locate the adjustable foot you wish to adjust on the underside of the projector. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector. Tilt-Adjustment Feet Tilt-Adjustment Ring Zoom, lens shift, and focus...
SETUP AND INSTALLATION Remote setup Installing / replacing the batteries Two AAA size batteries are supplied for the remote control. Remove the battery cover on the back of the remote control. Insert AAA batteries in the battery compartment as illustrated. Replace back cover on remote control.
Page 22
SETUP AND INSTALLATION Effective range Infra-Red (IR) remote control sensor is located on the top and front sides of the projector. Ensure to hold the remote control at an angle within 60 degrees perpendicular to the projector’s IR remote control sensor to function correctly.
USING THE PROJECTOR Powering on / off the projector Geometric Correction PIP/PBP Mode AV Mute ENTER Info. Source Re-Sync Volume D Zoom Menu Lens cap Format Freeze Remote S-Video HDMI1 HDMI2 Powering on HDBaseT Video HDMI3 Remove the lens cap. YPbPr DisplayPort Securely connect the power lead and signal/source cable.
USING THE PROJECTOR Geometric Correction PIP/PBP Selecting an input source Mode AV Mute Turn on the connected source that you want to display on the screen, such as computer, notebook, video player, etc. The projector will automatically detect the source. If multiple sources are connected, press the button on the projector keypad or the Source button on the remote control to select the desired input.
USING THE PROJECTOR Menu navigation and features The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. To open the OSD menu, press the button on the projector keypad or the Menu button on the remote control.
USING THE PROJECTOR OSD Menu tree Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Presentation Bright Cinema Display Mode Game sRGB DICOM SIM. User Off [Default] Blackboard Light Yellow Wall Color Light Green Light Blue Pink Gray Auto [Default]...
Page 27
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Warm Standard Color Temperature Cool Cold Red [Default] Green Blue Color Cyan Yellow Magenta Color Matching White(*) Hue / R(*) -50 ~ 50 [Default: 0] Saturation / G(*) -50 ~ 50 [Default: 0] Gain / B(*)
Page 28
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu -50 ~ 50 (depends on signal) H. Position [Default: 0] Signal -50 ~ 50 (depends on signal) V. Position [Default: 0] DynamicBlack Image Settings Power Brightness Mode (Power = 100%/ 95%/ 90%/ 85%/...
Page 29
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Audio 1 HDMI2 Audio 2 Default [Default] Audio 1 HDBaseT [Only for Audio 2 HDBaseT model] Default [Default] Audio 1 [Only for non-HDBaseT Audio 2 model] Audio Input...
Page 30
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Security Month Security Security Timer Hour Change [Default: 1234] Password [Default] HDMI Link [Default] Inclusive of TV HDMI Link Mutual [Default] Settings Power On Link PJ →...
Page 31
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Test Pattern [Default] Brightness Contrast Sleep Timer Remote Settings Color Matching [depends on Color Temp remote] Gamma Projection Projector ID 00 ~ 99 12V Trigger English [Default] Deutsch...
Page 32
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Top left Top right Menu Location Center [Default] Bottom left Menu Settings Bottom right Menu Timer 5sec 10sec [Default] Off [Default] Auto Source HDMI1/MHL HDMI2 Input Source...
Page 33
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu None Blue [Default] Background Options Color Green Gray Setup Logo Cancel [Default] Reset OSD Reset Cancel [Default] Reset to Default Network Status (read only) MAC Address (read only) Off [Default]...
Page 34
USING THE PROJECTOR Main Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values Menu Regulatory Serial Number Source Resolution 00x00 Refresh Rate 0.00Hz Display Mode Power Mode (Standby) Light Source 0 hr Hours Info Remote Code 00 ~ 99 Remote 00 ~ 99 Code(Active)
USING THE PROJECTOR Display menu Display image settings menu Display Mode There are many factory presets optimized for various types of images. Presentation: This mode is suitable for showing in front of public in connection to the PC. Bright: Maximum brightness from PC input.
Page 36
USING THE PROJECTOR Color Adjust a video image from black and white to fully saturated color. Tint Adjust the color balance of red and green. Gamma Set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to optimize your image output.
Page 37
USING THE PROJECTOR Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto, RGB(0-255), RGB(16-235), and YUV. White Level: Allow user to adjust White Level when inputting Video signals. Note: White level can only be adjusted for Video/S-Video input sources. ...
USING THE PROJECTOR Display 3D menu Note: This projector is a 3D ready projector with DLP-Link 3D solution. Please make sure your 3D glasses are use for DLP-Link 3D before enjoy your video. This projector supports frame sequential (page-flip) 3D via HDMI1/HDMI2/VGA ports. ...
USING THE PROJECTOR Display aspect ratio menu Aspect Ratio Select the aspect ratio of the displayed image between the following options: 4:3: This format is for 4:3 input sources. 16:9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV. ...
USING THE PROJECTOR Auto Keystone Correct keystone digitally to fit the projected image on the area on which you are projecting. Note: The image size will reduce slightly when adjusting the horizontal and vertical keystone. When the Auto Keystone is used, the Four Corner Adjustment function will be disabled. Reset Return the factory default settings for geometric correction settings.
USING THE PROJECTOR Setup menu Setup projection menu Projection Select the preferred projection between front, rear, ceiling-top, and rear-top. Setup screen type menu Screen Type (for WXGA or WUXGA model only) Choose the screen type from 16:9 and 16:10. Setup power settings menu Direct Power On Choose “On”...
USING THE PROJECTOR Setup security menu Security Enable this function to prompt for a password before using the projector. On: Choose “On” to use security verification when the turning on the projector. Off: Choose “Off” to be able to switch on the projector without password verification. Security Timer Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used.
USING THE PROJECTOR Setup remote settings menu IR Function Set the IR function setting. On: Choose “On”, the projector can be operated by the remote control from the top and front IR receivers. Off: Choose “Off”, the projector can’t be operated by the remote control. By selecting “Off”, you will be able to use the Keypad keys.
USING THE PROJECTOR Menu Settings Set the menu location on the screen and configure menu timer settings. Menu Location: Select the menu location on the display screen. Menu Timer: Set the duration where the OSD menu stays visible on the screen. Auto Source Choose this option to let the projector automatically find an available input source.
USING THE PROJECTOR Network menu Network LAN menu Network Status Display the network connection status (read-only). MAC Address Display the MAC address (read-only). DHCP Use this option to enable or disable the DHCP function. Off: To assign IP, subnet mask, gateway, and DNS configuration manually. ...
USING THE PROJECTOR Making a direct connection from your computer to the projector* Turn “Off” the DHCP option on the projector. Configure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”). Open Network and Sharing Center page on your PC, and assign the identical network parameters to your PC as set on projector.
USING THE PROJECTOR Setup network control settings menu LAN_RJ45 function For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness, and contrast settings.
Page 53
USING THE PROJECTOR LAN RJ45 Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop). On the PC (Laptop), select Start > Control Panel > Network Connections. Right-click on the Local Area Connection, and select Property. In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).
Page 54
USING THE PROJECTOR Click “Properties”. Type in the IP address and Subnet mask, then press “OK”. Press the “Menu” button on the projector. Open on projector Network > LAN. Enter the following connection parameters: ± DHCP: Off ± IP Address: 192.168.0.100 ±...
Page 55
USING THE PROJECTOR The projector is setup for remote management. The LAN / RJ45 function displays as follows: Information page Main page Tool page Contact IT helpdesk English...
Page 56
USING THE PROJECTOR RS232 by Telnet Function There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45 interface. Quick Start-Guide for “RS232 by Telnet” Check and get the IP address on OSD of the projector. ...
USING THE PROJECTOR Info menu Info menu View the projector information as listed below: Regulatory Serial Number Source Resolution Refresh Rate Display Mode Power Mode (Standby) Light Source Hours Remote Code ...
MAINTENANCE Installing and cleaning the dust filter Installing the dust filter Note: Dust filters are only required/supplied in the selected regions with excessive dust. Cleaning the dust filter We recommend you to clean the dust filter every three months. Clean it more often if the projector is used in a dusty environment.
ADDITIONAL INFORMATION Compatible resolutions Digital (HDMI 1.4) Native resolution: 1920 x 1080 @60Hz (ZH506); 1920 x 1200 @ 60Hz (WU506) Descriptor timing -B0 Descriptor timing -B1 Established Timing Standard Timing Supported Video Mode (Detail timing) (Detail timing) 720 x 400 @ 70Hz...
Page 60
3840 x 2160 @ 60Hz 4096 x 2160 @ 50Hz 4096 x 2160 @ 60Hz Analog Native resolution: 1920 x 1080 @ 60Hz (ZH506); 1920 x 1200 @ 60Hz (WU506) B0 / Established Timing B0 / Standard Timing B0 / Detail Timing...
Page 61
If 3D input is 1080p@24Hz, the DMD should replay with integral multiple with 3D mode. Support NVIDIA 3DTV Play if there is no patent fee from Optoma. 1080i@25Hz and 720p@50Hz will run in 100Hz; 1080p@24Hz will run in 144Hz; other 3D timing will run in 120Hz.
ADDITIONAL INFORMATION Projector dimensions and ceiling mount installation To prevent damage to your projector, please use the Optoma ceiling mount. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: ...
ADDITIONAL INFORMATION IR remote codes Geometric Correction PIP/PBP Mode AV Mute ENTER Info. Source Re-Sync Volume D Zoom Menu Format Freeze Remote S-Video HDMI1 HDMI2 HDBaseT Video HDMI3 YPbPr DisplayPort Key code Printing-key BYTE1 BYTE2 BYTE3 BYTE4 Repeat definition customer 0 customer 1 data 0 data 1...
Page 67
ADDITIONAL INFORMATION Key code Printing-key BYTE1 BYTE2 BYTE3 BYTE4 Repeat definition customer 0 customer 1 data 0 data 1 Laser Laser Source Source #BYTE3 #BYTE3 Re-Sync Re-Sync #BYTE3 Volume + #BYTE3 Volume Volume - #BYTE3 D Zoom + #BYTE3 D Zoom D Zoom - #BYTE3 Menu...
ADDITIONAL INFORMATION Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image problems No image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the "Installation"...
Page 69
ADDITIONAL INFORMATION Other problems The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Remote control problems If the remote control does not work ...
ADDITIONAL INFORMATION Warning indicators When the warning indicators (see below) light up or flash, the projector will automatically shutdown: “Lamp” LED indicator is lit red and if “Power” indicator flashes red. “Temp” LED indicator is lit red and if “Power” indicator flashes red. This indicates the projector has overheated.
ADDITIONAL INFORMATION Optoma global offices For service or support, please contact your local office. Japan 47697 Westinghouse Drive, 888-289-6786 東京都足立区綾瀬3-25-18 Fremont, CA 94539, USA 510-897-8601 info@os-worldwide.com 株式会社オーエス www.optomausa.com services@optoma.com 0120-380-495 www.os-worldwide.com コンタク トセンター: Canada Taiwan 47697 Westinghouse Drive, 888-289-6786 12F., No.213, Sec. 3, Beixin Rd.,...