EXCELL PRECISION CO., LTD. Table of Contents PRECAUTIONS FOR USE ......................3 PREPARATIONS BEFORE USING ..................... 3 CHAPTER 1 DISPLAY AND KEYPAD DESCRIPTIONS ............. 5 1-1 D ......................5 ISPLAY ESCRIPTIONS 1-2 P ................6 OWER UPPLY AND OWER ONSUMPTION 1-3 K ......................
Page 4
ZERO display . Press MC key to show firmware version 03005 (H4 series) or 03006 (X series). Press MC key again to show maintenance number XXX ranged from 000~999. Turn off and turn on scale to return to weighing mode.
When the low power warning symbol flashes, If not charge immediately, auto shut-down within 5~10 hours or 1~2 hours with backlight for H4 series. For X series, it auto shut-down within 8~12 hours or 3~6 hours with backlight. Once it auto shut-down and enter the battery protection mode, it must be charged before it can be used.
Page 6
EXCELL PRECISION CO., LTD. Lead-Acid Battery Notice Lead-acid battery adopts the advanced free-maintaining technique, customers need not to replenish electrolyte. The scale should be recharged every 3 months to battery over-discharged and shorten the life of the battery. 1. The battery should be fully charged for 8~10 hours.
EXCELL PRECISION CO., LTD. 1-2 Power Supply and Power Consumption 100~240Vac, 50/60Hz H4 series X series Software version 03005XXX 03006XXX Battery 6V / 4Ah lead acid battery 3.7V / 6100mAh Li battery Consumption 33mA / 0.20W 27mA / 0.11W (without backlight)
EXCELL PRECISION CO., LTD. Key Function Number key for setting the unit weight, quantity and etc. Clear key to clear the digits on the display. Unit weight key for setting the unit weight of sample. Press this key, the display returns to 0.
EXCELL PRECISION CO., LTD. Chapter 2 Operation 2-1 Power On SW switch on (Press SW to location “ ”) WEIGHT UNIT WEIGHT QUANTITY After stable, the scale will count back to zero. WEIGHT UNIT WEIGHT QUANTITY 600 ⇒ Maximum countable data: 600 000 Sampling Speed After return to zero and being stable, scale will enter into counting mode.
EXCELL PRECISION CO., LTD. 3. Press key while total column number is flashing SAMPLE Weight on platter 4. After stable, the scale finishes sampling and enters into counting mode stable Weight on platter Unit weight of object Enter sampling quantity 2-4-2 Enter Known Unit Weight 1.
EXCELL PRECISION CO., LTD. 2-5 Tare Function Operation 1. Place the packaging container on platter Weight of packaging container 2. Press TARE 3. The scale will enter into counting mode after stable stable Clear off the tare value Mode 1: After removing the object together with packaging container, weight column will display the negative value of packaging container.
EXCELL PRECISION CO., LTD. 3. Press TARE stable Weight of the object without container Unit weight of the object Quantity without packaging container Pre-Tare function is also available even if tare is in operation. If the net weight on platter is more than zero weight, the tare function is available. Otherwise, it’s not capable of tare function.
EXCELL PRECISION CO., LTD. Recall quantity accumulation While weight column displays 0, press key to recall the accumulated data + stable Accumulated total weight Accumulated total counts Accumulated total quantity Clear off the accumulated quantity value...
EXCELL PRECISION CO., LTD. 2-10 ID Input key, and the screen displays “- - - - - -”. Press Press key before it disappears. ZERO ID could be set up to 12 digits. They can be numbers (0~9), Enter ID with number keys English letters (A~Z), or ...
EXCELL PRECISION CO., LTD. Press key again U.W. PST Press number keys to select 1 of 50 addresses for saving the data. If it is over 50, Please re-enter. Press U.W. PST 2-12-2 Pre-set Unit Weight Saving Operation (Read-out) Press key again U.W.
EXCELL PRECISION CO., LTD. 3-1-2 Auto. Power-off Setting Press key and enter parameter 00~10. Then press key to save the setting. Default Setting: 00; up to 10 minutes at most. 00 Auto Power-off function is off. 01~10 Scale is automatically powered off after not in use for 1~10 minutes.
EXCELL PRECISION CO., LTD. 3-1-8 Accumulation Ending Mode Setting Press key and enter parameter 00~02. Then press key to save the setting. Default Setting: 00 00 Press key. Displays accumulation for 3 seconds, and return to weighing mode. 01 Press key.
EXCELL PRECISION CO., LTD. 3-2 External Weight and G Value Calibration EC 00 Return to previous level EC 01 External weight calibration Press EC 02 Calibrate G value used in local or in verification Approval model (CFn 01 = 02~04) do not have Enter parameter 00~03 02 EC.
EXCELL PRECISION CO., LTD. 3-2-2 Calibrate G Value Used in Local or in Verification It is capable for users to set or modify G value for 9 times. If it is the 10 revised G value, please enter “06 CGr” to calibrate local G value, and the calibration time will be re-set as “1”.
EXCELL PRECISION CO., LTD. 3-3 RS-232 and Serial Printer Setting r S 1 00 Return to previous level r S 1 01 Baud rate setting Press r S 1 02 Communication protocol setting r S 1 03 ...
EXCELL PRECISION CO., LTD. Please see “Appendix 1” for output format. Fixed format is described as following: Fixed format 2 “Press Fixed format 1 “Press M+ key to print” key to print” xxxxxxx xxxxx ITEM: xxxxxxx xxxxx 2.480 2.480 2.000...
EXCELL PRECISION CO., LTD. If parameter in rS1 03 is set as 02, it is not capable of continuous transmission mode. If parameter in rS1 03 is set as 03 ~ 07, it is capable of continuous transmission mode.
EXCELL PRECISION CO., LTD. 2. Press key to print “ “ <LF> <LF> <LF> <LF> <LF> <LF> <LF> TN: Total number TW: Total weights TA: Total quantities tn: Total number tw: Total weights ta: Total quantities NOTE: Fill in zero “0” for the blanks on the left.
EXCELL PRECISION CO., LTD. 3-3-8 Weight Band Setting for Auto. Transmission Press key and enter parameter 00~99. Then press key to save the setting. Default Setting: 05 (External value “5d”) 00 External value “0d” 01 External value “1d”...
Page 28
EXCELL PRECISION CO., LTD. and return value is 255. Command Format C According to the command format to modify ID,ITEM ,PT, UW : CR LF ITEM: CR LF CR LF CR LF Description: 1. 2 previous code is command code (must be capital letter),A is 0-9 or A-Z. Other symbol is unacceptable (because it can’t be showed on LCD).