Charging The Battery, Leds; Activating And Deactivating Bluetooth® Radio Interface - Stihl HTA 66 Instruction Manual

6 Charging the Battery, LEDs

► Ensure that the following components are in a
safe condition:
– Pole Pruner, 4.6.1.
– Guide bar, 4.6.2.
– Saw chain, 4.6.3.
– Battery, 4.6.4.
► Check the battery,
► Fully charge battery as described in the User
Manual for the STIHL AL 101, 300, 301-4, 500
chargers.
► Clean the pole pruner,
► Assemble the pole pruner (HTA 86),
► Mount the guide bar and saw chain,
► Tension the saw chain,
► Fill up with saw chain oil,
► Adjust the shaft length (HTA 86),
► Fit and adjust the carrying system,
► Check the controls,
► Check the chain lubrication,
► If you cannot carry out this work: Do not use
your pole pruner and contact your STIHL
dealer for assistance.
5.2 Connecting the Battery with the
STIHL App by means of a
Bluetooth
► Activate the Bluetooth
mobile device.
► Activating the Bluetooth
the battery, 7.1.
► Download STIHL App from the app store of
your mobile device and create an account.
► Open and sign in on the STIHL App.
► Add the battery in the STIHL App and follow
the instructions on the screen.
For contacts and other information, please visit
https://support.stihl.com or the app.
The STIHL connected feature is available in the
STIHL App in certain markets.
6 Charging the Battery, LEDs
6.1 Charging the Battery
The charging time depends on various factors,
e.g. the battery temperature or the ambient tem‐
perature. The actual charging time may vary
from the charging time indicated. The charging
time is indicated at www.stihl.com/charging-
times.
► Recharge the battery as described in the User
Manual for the STIHL AL 101, 300, 301-4, 500
chargers.
0458-191-9821-B
11.6.
16.1.
8.1.
8.2.1.
8.3.
8.4.
12.1.
12.2.
11.4.
11.5.
Radio Interface
®
®
radio interface on the
®
radio interface on
6.2 Displaying the charge level
1
► Press the button (1).
The LEDs light up green for about 5 seconds
and indicate the state of charge.
► If the LED on the right flashes green: Charge
the battery.
6.3 LEDs on Battery
The LEDs can show the state of charge or mal‐
functions. The LEDs can glow or flash green or
red.
The state of charge is indicated when the LEDs
glow or flash green.
► If the LEDs glow or flash red: Troubleshooting,
19.
There is a malfunction in the pole pruner or
battery.
7 Activating and Deactivating
Bluetooth® Radio Interface
7.1
Activating the Bluetooth
Interface
► If the battery is equipped with a Bluetooth
radio interface: press the button and hold it
depressed for about 3 seconds.
The "BLUETOOTH
bol lights up blue for about 3 seconds. The
®
Bluetooth radio interface on the battery is
activated.
7.2
Deactivating the Bluetooth
Radio Interface
► If the battery is equipped with a Bluetooth
radio interface: press the button and hold it
depressed for about 3 seconds.
The "BLUETOOTH
bol flashes blue for six times. The Blue‐
®
tooth radio interface on the battery is deacti‐
vated.
English
80-100%
60-80%
40-60%
0-20%
Radio
®
®
" LED next to the sym‐
®
®
" LED next to the sym‐
20-40%
®
®
39