Sampling With A Specified Tempo; Using A Count-In; Resampling - Roland SP-404SX Owner's Manual

Sampling with a Specified
Tempo
If you specify the BPM (tempo) while you're still in
sampling standby mode, the end point (the timing at
which the sound stops playing) will be automatically set
after sampling to a beat of the BPM value you specified .
1. Prepare.for.sampling.as.described.in.steps.1–6.of.
"STEP.2:.Sampling".(p ..18) .
2. Adjust.the.tempo.as.described.in."Adjusting.the.
Tempo".(p ..15) .
3. Press.the.[REC].button.to.start.sampling .
4. Press.the.[REC].button.once.again.to.stop.
sampling .
MEMO
• When sampling ends, the end point will automatically
be set according to the BPM, and the [MARK] button
will light . Refer to "Adjusting the Playback Region of a
Sample" (p . 27) .
• If the sampled time is multiple measures or less than
one measure, the BPM indication may be double or half .
In this case, press the [TIME/BPM] button so the button
is lit, then turn the [CTRL 2] (BPM) knob to set the
desired value . Refer to "Changing a Sample's BPM" (p . 30) .
• The displayed BPM value is an approximation derived
from the sampled time, and may not be accurate .
• Depending on the BPM value, the time corresponding
to the BPM may not precisely match the time from the
start point to the end point . For this reason if you use
Loop playback (p . 12) to continuously play a sample for
an extended time, the timing will gradually drift .

Using a Count-in

You can add a count-in (1, 2, 3, 4) when you start sampling .
This is convenient when you are sampling with a specific
tempo or time signature in mind .
1. Specify.the.tempo.as.described.in.steps.1–2.of.
"Sampling.with.a.Specified.Tempo".(p ..26)
2. Press.the.[START/END/LEVEL].button.so.the.
button.is.lit .
3. Press.the.[REC].button .
The metronome will sound, and the display will succes-
sively indicate .
-1- - 2 - - 3 -
" " -> " " -> "
Sampling will begin when the "
26
- 4- rE C
" -> " " -> " . "
r EC
" indication appears .

Resampling

You can play back a sample with an effect applied, and
then newly sample the result . This is called "resampling . "
1. Make.sure.that.the.[PATTERN.SELECT].button.is.
extinguished .
If it is lit, press the [PATTERN SELECT] button to turn it off .
2. Apply.an.effect.to.the.original.sample,.and.adjust.
the.effect.parameters .
3. Press.the.[RESAMPLE].button.so.the.button.is.lit ..
The display will indicate "
4. Play.back.the.original.sample .
5. Adjust.the.[CTRL.3].(LEVEL).knob.so.that.the.
display.illumination.does.not.light.red .
MEMO
While the [RESAMPLE] button is lit, you can't use the
[CTRL 3] knob to adjust the effect depth . If you want to
use the [CTRL 3] knob to adjust the effect depth, press
the [CANCEL] button to make the [RESAMPLE] button
go out .
6. Press.the.[REC].button.so.the.button.is.blinking ..
The bank buttons and pads to which resampling is
possible will start blinking .
7. Press.the.pad.to.which.you.want.to.resample,.so.
the.pad.is.lit .
You can also resample to a different bank .
NOTE
You can't resample to a pad to which a sample is
already assigned .
8. Use.the.[STEREO].button.to.specify.the.stereo/
mono.setting .
For details, refer to step 5 of p . 18 .
9. Press.the.[REC].button.so.the.button.is.lit .
Resampling will not yet begin at this point .
10. Press.the.pad.to.which.you.want.to.resample .
The sample will begin playing, and resampling will start .
NOTE
Never turn off the power during resampling . Turning off
the power at this time may destroy not only the sample
being resampled, but also other samples as well .
11. When.resampling.is.finished,.press.the.[REC].
button .
MEMO
During resampling, you can simultaneously play up to
four monaural samples or two stereo samples .
LEU
. "