Downloading - DSC Power 864 Installation Manual

Cross Zone Police Code. . . . . . . . . . . . . . . . . . . . .Section [328]
Burglary Verified Timer . . . . . . . . . . . . . . . . . . . . .Section [176]
Double Hit . . . . . . . . . . . . . . . . . . . . . Section [017], option [4]
Delinquency Reporting
The Delinquency feature is used to monitor system activity. When
the Delinquency Transmission Delay timer expires, the panel
will transmit the Delinquency reporting code.
If the system is programmed to monitor Activity Delinquency,
the timer will be programmed in hours. The timer will start under
the following conditions:
• When the system is armed in the Stay mode
• When the system is disarmed
• When a zone is violated and restored while the system is dis-
armed/Stay armed (Interior, Interior Delay, Interior Stay/Away,
or Delay Stay/Away zones only).
The activity delinquency timer will be ignored when the system is
armed in the Away mode. Zones that are bypassed in the [*][1]
Bypass menu will not reset the timer.
If the system is programmed to monitor Closing Delinquency,
the timer will be programmed in days. The timer will restart every
time the system is disarmed.
Activity/Closing Delinquency . . . . . . . . Section [380], option [8]
Delinquency Transmission Delay . . . . . . . . . . . . . .Section [377]
Maintenance
The panel will transmit a Battery Trouble Alarm Reporting
Code when the backup battery drops below 11.5 V
tery Trouble Restoral Reporting Code will not be transmitted
until the battery has been charged over 12.5 V
To prevent the panel from transmitting an AC Failure Trouble
Alarm Reporting Code during short power outages the panel
will not send the signal unless AC power is lost for the amount of
minutes programmed for the AC Failure Communication
Delay. The AC Failure Trouble Restoral Reporting Code will be
transmitted once AC power has been restored for the amount of
time programmed for AC Failure. Communication delays.
NOTES: If AC Failure Communications Delay is programmed as
000, the AC Failure Trouble reporting code will be sent immedi-
ately.
For proper communication of PC5204 AC troubles, program the
AC Failure Communication Delay as "000".
A Bell Circuit Trouble Alarm Reporting Code will be transmit-
ted immediately if an open condition is measured on the Bell
Output of the main panel. The Bell Circuit Trouble Restoral
Reporting Code will be transmitted as soon as the problem is cor-
rected.
A Fire Trouble Alarm Reporting Code will be transmitted imme-
diately when an open condition is measured on any Fire type
zone (see section 5.1 "Zone Definitions" on page 20). The Fire
Trouble Restoral Reporting Code will be transmitted as soon as
the problem is corrected.
The Auxiliary Power Supply Trouble Alarm Reporting Code
will be transmitted if the AUX output is shorted. The AUX output
control incorporates a fuseless design. When excessive current is
drawn the panel will automatically shut off the output. The panel
will constantly check the AUX output and when the excessive
current draw is removed the panel will reset the output and
26
transmit an Auxiliary Power Supply Trouble Restoral Report-
ing Code.
A TLM Trouble Reporting Code can only be transmitted if a
LINKS1000/GSM1000/LINKS2X50 Communicator is being used
(see section 5.26 "LINKS1000/GSM1000 Cellular Communica-
tor" on page 33). The panel will only transmit the signal after the
time programmed for the TLM Trouble Delay. The TLM Restoral
Reporting Code will be transmitted immediately once the trouble
is restored.
A General System Trouble Reporting Code will be transmitted
if the panel detects any of the following on the PC5204 Power
Supply/Output Module: AC Power Failure, Low Battery, AUX Out-
put Trouble, Output #1 Supervisory trouble. The General Sys-
tem Trouble Restoral Reporting Code will be transmitted when
all of the listed problems are corrected.
A General System Supervisory Trouble Reporting Code will
be transmitted if any module goes missing from the Keybus. If
the module is a zone expander the panel will also transmit the
Zone Expander Supervisory Alarm Trouble Reporting Code.
The panel will send a General System Supervisory Restoral
Reporting Code when the problem is corrected as well as a Zone
Expander Supervisory Restoral Reporting Code if the module
is a zone expander.
NOTE: If a PC5132 has a supervisory trouble, the panel will
signal a Zone Expander Supervisory alarm, even if only
Wireless Keys are enrolled on the module.
Zone Restorals
If the Restoral on Bell Time-out option is selected, the panel
will send the Zone Restoral Reporting Code for the zone if the
. The Bat-
DC
bell cut-off time has expired and the zone is secured. If the zone
is not secured when the bell cut-off time expires, the panel will
.
DC
send the restoral immediately once the zone is secured, or when
the system is disarmed. If the Restoral on Bell Time-out option
is not selected, the panel will immediately send the Zone Resto-
ral Reporting Code when the zone is secured, regardless of
whether or not the alarm output is active.
NOTE:24 Hour type zones will report the restoral immedi-
ately when the zone is secured.
Restoral on Bell Time-out . . . . . . . . . . Section [380], Option [2]
AC Failure Communication Delay Time. . . . . . . . . Section [377]
5.9
Downloading allows programming of the entire control panel via
a computer, modem and telephone line. All functions and fea-
tures, changes and status, such as trouble conditions and open
zones can be viewed or programmed by downloading.
NOTE:When power is applied to the panel, a 6 hour down-
loading window can be enabled. This will allow you to per-
form downloading without having to do any keypad
programming.
NOTE: When an event occurs that the system is pro-
grammed to communicate to the central station, the panel
will disconnect from the downloading computer and report
the event. This will happen for all events except test trans-
missions.
If the Answering Machine/Double Call option is enabled (or
during the first 6 hours after power up) the panel will answer

Downloading