Downloading; Pgm Output Options - DSC PC1555 Installation Manual

Hide thumbs Also See for PC1555:
Table of Contents

Advertisement

Hex [C] - simulates the [#] key on a touch tone telephone
Hex [D] - forces the panel to search for dial tone
Hex [E] - two second pause
Hex [F] - marks the end of the telephone number
The panel will attempt to call the pager once. Once the appro-
priate telephone number is dialed, the panel will send the
account number and Reporting Code followed by the [#] key
(Hex [C]).
The panel has no way of confirming if the pager was called
successfully. A Failure To Communicate trouble will only be
generated if the panel detects a busy tone on all dialing
attempts, or if no dial tone is detected on all dialing attempts.
The pager format will not cause any form of ringback.
NOTE:The Pager Format cannot be used with the LINKS1000
cellular communicator.
NOTE:Do not use the digit C in a reporting code when using
Pager Format. In most cases, the digit C will be interpreted as
a [#], which will terminate the page before it has finished.
NOTE:If the panel detects a busy signal, it will attempt to page
again. It will make the maximum number of attempts pro-
grammed in section [160].
NOTE:Force dialing should be disabled when using Pager for-
mat.
NOTE:When using Pager format, you must program two hex
digit E's at the end of the telephone number

5.10 Downloading

The required downloading software is DLS-1 v6.7 and up.
Downloading allows you to program the entire control panel
via a computer, a modem and a telephone line. All functions,
features, their changes and status – such as trouble condi-
tions and open zones – can be viewed or programmed
through downloading.
NOTE:Downloading is always enabled for six hours each time
the panel is powered up, unless the User Can Enable DLS
Window option is disabled
The panel will answer calls for downloading when the pro-
grammed Number of Rings is heard by the panel.
If the Answering Machine/Double Call option is enabled (or
during the first six hours after power up), the panel will answer
incoming calls for downloading in the following manner:
1. The panel hears one or two rings then misses a ring.
2. At this point the panel will start a the double-call timer.
3. If the panel hears another ring before the Answering
Machine Double-Call Timer expires, it will answer on the
first ring of the second call.
The panel will immediately go on line and begin downloading.
If the Call-Back option is enabled, the panel and the com-
puter will both hang up. The panel will then call the Down-
loading Computer's Telephone Number and wait for the
computer to answer. Once the computer answers, download-
ing will begin.
If the User Enabled DLS Window option is ON, the user can
activate the downloading feature by entering [*][6][Master
Code][5].
If the User Initiated Call-Up option is enabled, the user can
have the panel initiate a call to the downloading computer by
pressing [*][6][Master Code][6].
The Download Access Code and Panel Identifier Code are
for security and proper identification. Both the panel and the
20
computer file should contain the same information pro-
grammed before attempting to download.
The time to complete a successful download can be signifi-
cantly reduced with the use of the PC-LINK. This adaptor
makes it possible to perform on-site downloading. To Initiate
Local Downloading via the PC-LINK, enter [*][8][Installer's
Code][499][Installer's Code][499]. All keypads will be busy for
the duration of the PC-LINK connection. The status LEDs will
display the current system status on the keypad where the
PC-LINK was initiated. For more information on connecting the
PC-LINK, refer to your "PC-LINK Download Kit Instruction
Sheet".
NOTE: When a zone status upload is performed through PC-
LINK, the information uploaded may not be accurate. For more
information, refer to your DLS-1 manual.
Downloading can also be performed through the LINKS1000
cellular communicator if the telephone line is disconnected. If
using the LINKS1000 with call back, you need to program the
LINKS1000 Preamble with the downloading telephone num-
ber in order for the panel to call the computer correctly.
NOTE:When uploading labels from LCD keypads, only labels
from the LCD keypad assigned to slot 8 will be uploaded.
Answering Machine/Double Call . . . . . . . . Section [401]: [1]
User Enable DLS Window . . . . . . . . . . . . . Section [401]: [2]
Call-Back . . . . . . . . . . . . . . . . . . . . . . . . . . Section [401]: [3]
User-initiated Call-up enabled/disabled . . . Section [401]: [4]
Downloading Computer's Telephone Number . Section [402]
Downloading Access Code . . . . . . . . . . . . . . . Section [403]
Panel Identification Code . . . . . . . . . . . . . . . . . Section [404]
Answering Machine Double Call Timer . . . . . . Section [405]
Number of Rings to Answer On . . . . . . . . . . . . Section [406]
LINKS1000 Preamble (Downloading) . . . . . . . . Section [490]
Initiate Local Downloading (PC-LINK) . . . . . . . Section [499]

5.11 PGM Output Options

Program the programmable outputs PGM1 and PGM2 on the
main board by selecting one of the output options listed below
(exceptions noted).
Main Board PGM Outputs. . . . . . . . . . . . . . . . . Section [009]
NOTE: PGM outputs cannot be completely disabled in
installer's programming. To disable a PGM output completely,
you must remove all wiring from the output.
[01] Burglary and Fire Bell Output
The output will activate when the alarm output is active and
will deactivate when the alarm output is silenced. If the alarm
output is pulsing, the PGM output will pulse as well. This out-
put will follow the activation of the alarm output (pre-alert) for
delayed fire zones.
[02] For future use
[03] Sensor Reset ([*][7][2])
NOTE:This output will normally be active (switched to ground).
This option is used to reset power for latching smoke detec-
tors. The output will deactivate for five seconds when the
[*][7][2] command is entered. (See "[*][7] Command Output
Functions" on page 11.) The keypad buzzer will not sound for
the five second period.
Please refer to the Control Panel Wiring Diagram in this man-
ual for wiring instructions.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents