Page 8
• フラットケーブルを抜くときは、1 マザーボード上のコ ネクター両側のロックを上げて外してから、2 ケーブル を引き抜いてください。 • ハーネスはフェライトコアからも外してください。 ご注意 フェライトコアは、PDW-F75 およびシリアルナンバーが 11001 以降の PDW-F70 には付属していません。 フロントパネルを固定しているネジ(3 箇所)を外す。 A C C E S S N E TW O R K LO C R E M O TE L E V E P H O N E S C H A...
Page 11
1 2個所ABの穴でKY-580基板の位置決めをする。 2 板金を取り付け、ネジを締める。 3 残り 7 箇所のネジを締める。 4 ハーネスを HP-130 基板に差し込む。 KY-580 基板 板金 オプションパネル(裏) ハーネス HP-130 基板 フロントパネルから取り外したジョグ / シャトルダイヤル を、それぞれオプションパネルの受け軸の溝に合わせて付 け直す。 1 切り欠きが上になるようにシャトルダイヤルをはめる。 2 ジョグダイヤルを差し込む。 オプションパネル(表) 切り欠き N E TW O R K LO C R E M O TE L E V E P R O F E S P H O...
Page 13
フロントパネルを固定していた 3 本のネジを使用して、オ プションパネルを固定する。 N E TW O R K LO C R E M O TE L E V E P R O F E S P H O S IO N E S N A L D IS E C O C H A P T E...
Page 14
• フラットケーブルを奥まで差し込んだら、マザーボード 上のコネクター両側のロックを押し下げて固定してくだ さい。 • ハーネスはフェライトコアを通してから接続してくださ い。 ご注意 フェライトコアは、PDW-F75 およびシリアルナンバーが 11001 以降の PDW-F70 には付属していません。 PDW-F75 の場合のみ、図のように PDDL ラベル 1 を Professional Disc ロゴの上に、機種ラベル 2 を機種名 「PDW-F70」の上に、それぞれ元の表記が隠れるように貼 り付ける。 PDDL ラベル 1 Professional Disc ロゴ 機種ラベル 2 機種名「PDW-F70」 P R O F E S S I O N A L D I S...
Page 16
English Table of Contents Overview................17 Using This Manual ............17 Components of the PDBK-A640 ........18 Installation................20 Step 1: Removing the Top Panel of the Main Unit ..20 Step 2: Removing the Front Panel from the Main Unit ..21 Step 3: Replacing the Parts ..........23 Step 4: Attaching the Option Panel to the Main Unit ..26...
Overview The PDBK-A640 Professional Disc Cart Mount Kit is an option kit exclusive for the Sony PDW-F70/F75 Professional Disc Recorder. Attaching the option kit to the PDW-F70/F75 enables the recorder to be mounted in the PDJ-A640 Professional Disc Cart. Note Always verify that the unit is operating properly before use.
Components of the PDBK-A640 The PDBK-A640 consists of the following items: • PDBK-101 • Screw (+ PSW3 × 8) × 3 • NET-1 board • Installation Instructions • Front panel assembly N E TW O R K LO C R E M...
Page 19
Installation of the PDBK-101 in the PDW-F70 may require an upgrade of the firmware of the PDW-F70. Installation of the PDBK-101 in the PDW-F75 does not require an upgrade of the firmware of the PDW-F75. For details, ask your Sony dealer or a Sony service representative. Overview...
If this option is installed incorrectly, personal injury or damage to peripheral items may occur due to fire, shock, or other accidental circumstances. To avoid such risks, consult your Sony dealer or a Sony service representative for installation. Proceed as follows to attach the front panel assembly (hereinafter called “the option panel”) to the PDW-F70/F75 (hereinafter called “the main...
D IO 1 /2 1 /2 Step 2: Removing the Front Panel from the Main Unit Disconnect the flat cable and the harness from the motherboard. Ferrite core Motherboard Flat cable Harness • When disconnecting the flat cable, 1 raise and release the locks at both sides of the connector on the motherboard, 2 then pull out the cable.
Page 22
Note A PDW-F70 product of serial number of 11001 or higher, or the PDW-F75 has no ferrite core. Remove the three screws holding the front panel. A C C E S S N E TW O R K LO C R E M O TE L E V E...
Step 3: Replacing the Parts Remove the necessary parts from the front panel removed from the main unit and attach them to the option panel. Disconnect the harness from the HP-130 board of the front panel. Front panel (rear) HP-130 board (The option panel also has an HP-130 board in the same position.) Pull out the jog and shuttle dials from the front panel.
Page 24
Jog dial Jog dial Shuttle dial Front panel (front) Detach the KY-580 board from the front panel. First remove the screw 1 at the block securing a metal plate together, then the seven screws 2. Front panel (rear) Metal plate KY-580 board Attach the KY-580 board detached from the front panel to the option panel then connect the harness disconnected from the HP-...
Page 25
1 Determine the position of the KY-580 board with two holes A and B. 2 Attach the metal plate and secure the screw. 3 Secure the remaining seven screws. 4 Connect the harness to the HP-130 board. KY-580 board Metal plate Option panel (rear) Harness HP-130 board...
Step 4: Attaching the Option Panel to the Main Unit Pass the harness connected to the HP-130 board and the flat cable through the respective openings into the main unit then fit the three projections at the bottom of the option panel into the respective holes on the main unit.
Page 27
Attach the option panel so that the dowels on both sides of the main unit fit in the dowel holes of the frame metal of the option panel. Dowel hole Secure the option panel, using the three screws that were used to fix the front panel.
Page 28
Main unit Motherboard • After inserting the flat cable to the end of the receptacle on the motherboard, push down on the locks on both sides of the receptacle to secure. • Pass the harness through the ferrite core. Note A PDW-F70 product of serial number of 11001 or higher, or the PDW-F75 has no ferrite core.
Page 29
PDDL label 1 Professional Disc logo Model label 2 “PDW-F70” Model name P R O F E S S I O N A L D I S E C O C H A P T E R D E P D W - F 7 0 E X P A P A G...