Control Camera Ch; Stop Bit; [Rs232C Setup] Settings For Rs232C; Unit Address(System) - Panasonic WJ-HD316 Operating Instructions Manual

Baud Rate
Select communication speed for data transmission with
a connected device from the following.
4 800/9 600 /19 200 (bps)

Control Camera CH

It is possible to assign camera channels to the RS485
ports 1 and 2 as below.
[Screenshot 1]
Start operation from the "RS485 Setup" menu.
SETUP MENU
Camera Control
PS.DATA Setup
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
z Move the cursor to "Control Camera CH" using the
arrows button ($TD $TC) and press the SET button.
[Screenshot 2]
The "Control Camera CH" pop-up window will be displayed.
SETUP MENU
Camera Control
PS.DATA Setup
CAMERA
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
x Move the cursor to a desired cell in the "TERM" column
using the arrows button.
[Screenshot 3]
The cursor will move to the selected cell in the "TERM" col-
umn.
SETUP MENU
Camera Control
PS.DATA Setup CAMERA
RS485 Setup
RS232C Setup
NW Setup 1
NW Setup 2
NTP Setup
c Select a port by rotating the jog dial.
PORT 1: Control through the RS485 port 1.
PORT 2: Control through the RS485 port 2.
Repeat steps 2 and 3 to assign other camera channels
to be controlled through the RS485 ports.
110
Maintenance Recording Event Schedule
LIVE
Switcher Display Com System
Baud Rate
19200
Control Camera CH
SETUP
Data Bit 8
Parity NONE
1

Stop Bit

Maintenance Recording Event Schedule
LIVE
Switcher Display Com System
Control Camera CH
Baud Rate 19200
Control Camera CH
SETUP
TERM CAMERA TERM
Data Bit 8
CAM1 PORT1 CAM9 PORT2
NONE
Parity
CAM2 PORT1 CAM10 1 PORT2
Stop Bit
CAM3 PORT1 CAM11 PORT2
CAM4 PORT1 CAM12 PORT2
CAM5 PORT1 CAM13 PORT2
CAM6 PORT1 CAM14 PORT2
CAM7 PORT1 CAM15 PORT2
CAM8 PORT1 CAM16 PORT2
O K CANCEL
Maintenance Recording Event Schedule
LIVE
Switcher Display Com System
Control Camera CH
19200
Baud Rate
Control Camera CH SETUP
TERM CAMERA TERM
8
Data Bit
CAM1 PORT1 PORT1 CAM9 PORT2
NONE
Parity
1
CAM2 PORT1 CAM10 PORT2
Stop Bit
CAM3 PORT1 CAM11 PORT2
CAM4 PORT1 CAM12 PORT2
CAM5 PORT1 CAM13 PORT2
CAM6 PORT1 CAM14 PORT2
CAM7 PORT1 CAM15 PORT2
CAM8 PORT1 CAM16 PORT2
O K CANCEL
v Move the cursor to "OK" using the arrows button and
press the SET button.
Camera channels will be assigned and the "Control
Camera CH" menu will be closed.
Notes:
• When moving the cursor to "CANCEL" in step 4 and
press the SET button, the setting will be canceled
and the "Camera Number Setup" menu will be
closed.
• The assignment of camera channels will not be
applied until the SET button is pressed after moving
the cursor to "OK" in the step 4.
Data Bit
The data length for communication will be displayed.
It is impossible to change the value for this setting.
Parity
Methods to check a transmission error at communica-
tion will be displayed.
It is impossible to change the value for this setting.
Stop Bit
Number of stop bit will be displayed.
It is impossible to change the value for this setting.
r [RS232C Setup] Settings for RS232C
Perform the following settings for RS232C.
SETUP MENU
Maintenance Recording
Switcher Display
Unit Adress(System)
Camera Control
Baud Rate
PS.DATA Setup
Data Bit
RS485 Setup
Parity
Stop Bit
RS232C Setup
Retry Timing
NW Setup 1
NW Setup 2
NTP Setup

Unit Address(System)

A unit address (System) is a unique number assigning
to each system device. The addresses must be unique
to identify system devices when connecting multiple
system devices.
Numbers, "001"-"099", are to be assigned to the unit
addresses to the system devices.
Baud Rate
Select communication speed for data transmission with
a connected device from the following.
9 600/19 200/38 400 (bps)
Data Bit
Select a data length for communication from the follow-
ing.
7/8 bit
Event Schedule
LIVE
Com System
001
9600
8
NONE
1
OFF