Table of Contents
Advertisement
Warning system
$ HUMID
LCD display
The HUMID display lights.
Even after condensation detection has
been released, it will continue to flash
once a second for the next 80 minutes.
WARNING lamp
The lamp lights when condensation has
been detected.
Tally lamp
The lamp flashes four times a second.
Warning alarm
Operation differs depending on the setting
selected for HUMID OPE on the setting
menu.
OWhen the ON setting has been selected,
the alarm sounds four times a second
while recording is being performed.
When recording is not being performed,
it sounds continuously.
OWhen the OFF setting has been
selected, the alarm does not sound.
Viewfinder
The HUMID display lights for 3 seconds.
What the warning
Condensation has formed.
indicates
VTR unit's operation The VTR unit's operation differs depending
on the setting selected for HUMID OPE on
the setting menu.
OWhen the ON setting has been selected,
the VTR unit continues to operate.
OWhen the OFF setting has been
selected, the VTR unit continues with the
recording, but this operation will stop if
the tape sticks. Operation stops
immediately when an operation other
than recording is being performed.
For 80 minutes after condensation
detection is released, the drum will rotate
however no other operation is possible.
Remedial action
Stop the tape travel, and turn off the power.
If the HUMID display fails to go off even
when the power is turned off and back on,
wait until it goes off.
$ TAPE NEAR END
LCD display
TAPE
WARNING lamp
The lamp flashes once a second (during
recording).
Tally lamp
The lamp flashes once a second (during
recording).
Warning alarm
The alarm sounds once a second (during
recording).
This can be switched on the setting menu.
OThe remaining tape display flashes
Viewfinder
once a second (in the E-E mode).
OThe SAVE lamp flashes in tandem with
the warning alarm (when SAVE&TAPE
has been selected as the setting for the
SAVE LED item on the VTR VF
INDICATOR screen of VTR MENU).
O" = " flashes once a second (three
seconds during recording).
What the warning
The tape is approaching its end.
indicates
VTR unit's operation The VTR unit continues to operate.
Remedial action
Replace the cassette tape if necessary.
(continued)
This segment flashes.
E
F
$ TAPE END
LCD display
TAPE
WARNING lamp
The lamp lights (during stop and in the
standby OFF mode).
Tally lamp
The lamp flashes 4 times a second
(during stop and in the standby OFF
mode).
Warning alarm
The alarm sounds continuously (during
stop and in the standby OFF mode).
OThe SAVE lamp flashes four times a
Viewfinder
second during stop and in the standby
OFF mode (when SAVE&TAPE has
been selected as the setting for the
SAVE LED item on the VTR VF
INDICATOR screen of VTR MENU).
O" = " lights (during stop and in the
standby OFF mode).
What the warning
The tape has come to its end.
indicates
VTR unit's operation If recording, playback or fast forwarding is
in progress, the operation is stopped.
Remedial action
Rewind the tape.
Alternatively, replace the cassette tape.
$ BATTERY NEAR END
LCD display
BATT
WARNING lamp
The lamp flashes once a second.
Tally lamp
The lamp flashes once a second.
Warning alarm
The alarm sounds four times a second.
Viewfinder
The BATT display flashes once a second.
What the warning
The battery is near the end of its charge.
indicates
VTR unit's operation The VTR unit continues to operate.
Remedial action
Replace the battery if necessary.
$ BATTERY END
LCD display
BATT
WARNING lamp
The lamp lights.
Tally lamp
The lamp flashes once a second.
Warning alarm
The alarm sounds continuously.
Viewfinder
The BATT display lights.
What the warning
The battery is at the end of its charge.
indicates
VTR unit's operation All operation is stopped and the tape is
unloaded.
Only cassette eject operation is possible.
Remedial action
Replace the battery.
All the segments flash.
E
F
E
F
This segment flashes.
E
F
All the segments flash.
127
Advertisement
Table of Contents
