Table of Contents
Advertisement
Setting menu screens
MIC/AUDIO screen
Variable
Item
range
display
MIC LOWCUT
FRONT
USER
CH1
REAR
ENG
F&R
OFF
C U F
MIC LOWCUT
FRONT
USER
CH2
REAR
ENG
F&R
OFF
C U F
LIMITER
ON
USER
OFF
ENG
C U F
TEST TONE
NORMAL
USER
ALWAYS
ENG
OFF
CHSEL
C U F
<Note>
The frequency characteristics in the MIC LOWCUT ON mode are
200 Hz to 10 kHz.
120
VTR MAIN MENU (continued)
VF
Remarks
For setting the high-pass
filter for the CH1 mic input.
FRONT:The high-pass filter
for the front mic
input is set to ON.
REAR: The high-pass filter
for the rear mic
input is set to ON.
F&R:
The high-pass
filters for both the
front and rear mic
inputs are set to
ON.
OFF:
The high-pass filter
for the CH1 input is
set to OFF.
For setting the high-pass
filter for the CH2 mic input.
FRONT:The high-pass filter
for the front mic
input is set to ON.
REAR: The high-pass filter
for the rear mic
input is set to ON.
F&R:
The high-pass
filters for both the
front and rear mic
inputs are set to
ON.
OFF:
The high-pass filter
for the CH2 input is
set to OFF.
For switching the audio
limiter to ON or OFF.
ON : The limiter operates.
OFF : The limiter does not
operate.
NORMAL:
The test tone signal is
output when the AUDIO
IN switch for CH1 is set
to front while BAR is
selected as the
CAM/BAR switch setting.
ALWAYS:
The test tone signal is
always output when BAR
is selected as the
CAM/BAR switch setting.
OFF:
The test tone signal is
not output.
CHSEL:
The test tone signal is
output for the selected
channel when the
AUDIO IN switch CH1 or
CH2 is set to front while
BAR is selected as the
CAM/BAR switch setting.
Variable
Item
range
display
CUE SELECT
SIDE SW
USER
CH1
ENG
CH2
MIX
C U F
EMBEDDED
ON
USER
AUDIO (60 Hz)
OFF
ENG
C U F
A/V SYNCHRO
ON
USER
OFF
ENG
C U F
<Notes>
OWhen ON has been selected as the A/V SYNCHRO item setting,
noise may be carried on the audio signals at those moments
when the frame rate is switched.
OThe timing of the images and the timing of the sound are fixed
while recording is in progress. This means that these two timings
may not be in synchronization when the frame rate is switched
during recoding even when ON has been selected as the A/V
SYNCHRO item setting.
OAt frame rates of 12P and less, it is not possible for the timing of
the images and the timing of the sound to be in synchronization
even when ON has been selected as the A/V SYNCHRO item
setting. The 12P timing will be fixed.
The underlining in the variable range column indicates the setting in
the preset mode.
VF
Remarks
For setting the audio
signals to be recorded on
the cue track.
SIDE SW:
The signals selected by
the CUE switch on the
side panel are recorded.
CH1:
The CH1 signals are
recorded.
CH2:
The CH2 signals are
recorded.
MIX:
The CH1 and CH2
mixed signals are
recorded.
For setting whether the
embedded audio signals
are to be output to the HD
SDI MON connector and
HD SDI EE connector
when 60.00 Hz has been
selected as the frame
frequency setting.
ON : The embedded
audio signals are
output.
OFF : The embedded
audio signals are not
output.
At low frame rates, the
images lag behind the
sound. This item is used
to select whether this lag
is to be adjusted.
ON:
The lag is adjusted so
that the timing of the
images is more or less
in synchronization with
the timing of the sound.
OFF:
The lag is not adjusted.
The same operations as
in previous models are
performed.
Advertisement
Table of Contents
