Omron 3G8F5-DRM21 Operation Manual page 114

Error Messages
Error message
Specified slave has valid IN Data. To edit,
define valid IN Block.
Specified slave has valid OUT Data. Before
registering, define valid OUT Memory Block.
Specified slave has valid OUT Data. To edit,
define valid OUT Block.
Specified file or device can not be accessed, or
specified service be supported.
Specified file can not be used for this function.
Specified file can not be used for this device.
Wrong unit type or wrong corresponding PLC.
Can not allocate all devices to specified
memory block.
Part or all of specified area Allocated to other
device.
Specified word located in setup impossible
area.
Setup out of specified block or setup Allocated
to setup impossible area removed.
Slave Allocated to Node Address of Self Master
Unit or Configurator.
Because usable printer has not been set,
process can not be continued.
Already set to specified mode.
Other device already Allocated.
Can not set all blocks to "Not Used."
Out of setup possible maximum number of
words.
Setup possible parameters not exist.
Can not read selected files.
Less than 2 target masters selected.
Too large data.
Too large data.
Wrong Data.
Data value not match with Data Size.
Wring Data Format.
Device not selected.
100
Error processing
The Create Master Parameters or Edit Device Parameters command
could not allocate I/O memory to a Slave that requires both output and
input data because there is no input memory block. Define a usable
input memory block to edit the parameters.
The Master parameter wizard could not allocate I/O memory to a
Slave that requires output data because there is no output memory
block. Define a usable output memory block to register the Slave.
The Create Master Parameters or Edit Device Parameters command
could not allocate I/O memory to a Slave that requires both output and
input data because there is no output memory block. Define a usable
output memory block to edit the parameters.
Either the specified file/device doesn't exist or the specified command
isn't supported. Check the file/device.
Either an error occurred during communications or the specified
command isn't supported. Check that the other node is operating
properly.
Also, verify that the Configurator's baud rate matches the other node's
baud rate and check for wiring problems.
The specified file type is incorrect. Specify the correct file.
The specified parameter file was created for a different model. Specify
the correct file.
The output area or input area was made too small (not enough
words), so the Master parameter wizard couldn't allocate I/O to all of
the Slaves. Change the memory block settings.
Part or all of the specified area has already been allocated to another
device. Either allocate a different area or change the other device's
I/O allocation.
It isn't possible to set the specified words. Set another area.
Due to a change in memory block settings, all or part of the existing
allocation couldn't be allocated within the block. Reassign the I/O
allocation within the current area.
A Slave device is allocated to the node address of the Configurator or
a Master Unit. Correct the allocation.
A usable printer hasn't been set. Register the printer.
* The service can't be executed because it is already set to the
specified mode.
The area is already allocated to another device. Either allocate
another area or change the existing device's allocation.
All of the memory blocks can't be set to "Not Used." Enable at least
one of the blocks.
The specified Master parameter settings exceed the specified PC's
maximum number of words usable during remote I/O communications.
The specified device has no parameters that can be set.
There are too many files so some of the files could not be read.
Reduce the number of files.
Masters were not selected correctly for an I/O allocation duplication
check. Select two or more Masters.
* The other node attempted to transmit too much response data.
Reduce the requested data size.
* The other node attempted to receive too much data. Reduce the
transmitted data size.
The specified data is incorrect.
The specified data does not match the data size. Set correct data.
The data format is incorrect. Specify with the correct format.
A target device hasn't been selected. Select a target device.
Appendix B