Korg MS2000R Owner's Manual page 53

3 Use the [+/YES] [–/NO] keys to select the copy source
program.
4 Use CURSOR[®] to move the cursor to the copy
source timbre.
5 Use the [+/YES] [–/NO] keys to select the copy source
timbre.
If the copy source program is Single, it will not be possi-
ble to select the copy source timbre (only timbre 1 is
available).
6 Use the CURSOR [®] key to move the cursor to "OK,"
and press the [+/YES] key.
You will be asked to confirm the copy function.
26C UTILITY
Are You Sure OK?
7 Press the [+/YES] key once again.
The copy operation will be completed, and the display
will indicate "Completed."
8 Press the [EXIT] key.
You will return to the first screen of the "CopyTimbre"
function.
D: SwapTimbre
This function swaps (exchanges) the settings of timbres 1
and 2 in the currently selected program.
The swap function cannot be performed for Single pro-
grams.
Procedure
1 In LCD Edit mode press the SELECT [16] key, and then
press the CURSOR [®] key three times.
The LCD screen will show Page 26D: UTILITY "Swap-
Timbre."
26D UTILITY
SwapTimbre
2 Press the [+/YES] key.
You will be asked to confirm the swap function.
26D UTILITY
Are You Sure OK?
3 Press the [+/YES] key once again.
The timbres will be swapped, and the display will indi-
cate "Completed."
4 Press the [EXIT] key
You will return to the first screen of the "SwapTimbre"
function.
E: InitSeq
This function initializes one or all sequences of the currently
selected timbre.
InitSeq...................................................... [SEQ1...ALL]
Select the sequence(s) that you wish to initialize.
When you initialize a sequence, the data recorded in that
sequence will be erased.
Procedure
1 In LCD Edit mode press the SELECT [16] key, and then
press the CURSOR [®] key four times.
2 Press the [+/YES] key.
3 Use the [+/YES] [–/NO] keys to select the sequence that
4 Use CURSOR [®] to move the cursor to "OK," and
5 Press the [+/YES] key once again.
6 Press the [EXIT] key.
F: CopySeq
This function copies sequence data from another timbre to
the currently selected timbre.
Source Program......................................... [A01...H16]
Select the copy source program.
Source Timbre ..................................................... [1, 2]
OK?
Select the copy source timbre.
Source Seq ..................................................... [S1...S3]
Select the copy source sequence.
Destination Seq .................................................. [1...3]
Select the copy destination sequence.
Procedure
1 In LCD Edit mode, press the SELECT [16] key and then
2 Press the [+/YES] key.
The LCD screen will show Page 26E: UTILITY "InitSeq."
26E UTILITY
InitSeq
The LCD screen will show the sequence to be initialized
(InitSeq).
26E UTILITY
SEQ1
you wish to initialize.
If you select ALL, all sequences (SEQ 1–3) of the timbre
will be initialized.
press the [+/YES] key.
You will be asked to confirm the initialize function.
26E UTILITY
Are You Sure OK?
The sequence(s) will be initialized, and the display will
indicate "Completed."
You will return to the first screen of the "InitSeq" func-
tion.
press the CURSOR [®] key five times.
The LCD screen will show Page 26F: UTILITY "Copy-
Seq."
26F UTILITY
CopySeq
The LCD screen will indicate the copy source program
(Source Program), timbre (Source Timbre), sequence
(Source Seq), and copy destination sequence (Destina-
tion Seq).
26F UTILITY
A01 T:1 S1"1 OK?
Source Program
Source Timbre Source Seq
Parameter Guide
OK?
OK?
OK?
Destination Seq
47