Kenwood VR-9080 Instruction Manual page 24

Preparing for surround sound
9 Use the MULTI CONTROL knob or MULTI keys %/fi to select
the appropriate Surround Speaker setting.
If you selected "FRNT LARGE" as the Front Speaker setting,
1 SURR NML/THX : Average size Surround Speakers are con-
2 SURR LARGE
: Large size Surround Speakers are
3 SURR OFF
: Surround Speakers are not connected to
If you selected "FRNT NML/THX" as the Front Speaker setting,
1 SURR NML/THX : Average size Surround speakers are
2 SURR OFF
: Surround Speakers are not connected to
0 Press the 5 key or MULTI # key again to accept the setting.
• When the setting other than "SURR OFF" is selected, the
Surround Back Speaker setting indication "SB" appears.
• When the setting "SURR OFF" is selected, the procedure skips
to step @.
! Use the MULTI CONTROL knob or MULTI %/fi keys to select
appropriate Surround Back Speaker setting.
If you selected "SURR LARGE" as the Surround Speaker
setting,
1 SB NML/THXx1 : A single average size Surround Back
2 SB NML/THXx2 : A pair of average size Surround Back Speak-
3 SB LARGEx1
: A single large size Surround Back Speaker
4 SB LARGEx2
: A pair of large size Surround Back Speak-
5 SB OFF
: Surround Back Speakers are not connected
SP MUTE
A B CLIP
L C SW R
LFE
SL SB SR
If you selected "SURR NML/THX" as the Surround Speaker
setting,
1 SB NML/THXx1 : A single average size Surround Back
2 SB NML/THXx2 : A pair of average size Surround Back Speak-
3 SB OFF
: Surround Back Speakers are not connected
@ Press the MEMORY/ENTER key or the ENTER key to return to
the "SP SETUP" display.
2
Adjust the speaker volume level.
If you have a commercially available sound pressure meter, set the
meter readout to "C" at the listening position and adjust the sound
volume of each channel so that the noise level will reach 75dB. If you
do not have a sound pressure meter, start the volume level from 0db
and adjust so that the level from each speaker is almost the same.
• Indicators appear only for the channels of the speakers selected
in step 1 .
Be aware that the TEST TONE is quite a lod sound (0dB).
1 Press the 5/∞ keys or MULTI @/# keys to select the "SP LEVEL"
and press the MEMORY/ENTER key or the ENTER key.
24 EN
nected to the receiver.
connected to the receiver.
the receiver.
connected to the receiver.
the receiver.
Speaker is connected to the receiver.
ers are connected to the receiver.
is connected to the receiver.
ers are connected to the receiver.
to the receiver.
STEREO
Speaker is connected to the receiver.
ers are connected to the receiver.
to the receiver.
2 Press the 5/∞ keys or MULTI @/# keys for the following
displays:
1 T.TONE AUTO
2 T.TONE MANUAL : Adjust the volume level from each speaker
3 T.TONE OFF
4 RETURN
3 After selecting "T.TONE AUTO" or "T.TONE MANUAL",
press the MEMORY/ENTER key or the ENTER key to begin
TEST TONE.
Use the MULTI CONTROL knob or MULTI %/fi keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For T.TONE AUTO selection, the test tone is heard from the
speakers in the following sequence for 2 seconds each start-
ing from the Front Left speaker.
LEFT CNTR
SUBW
• If you have selected "SB NML/THXx1" or "SB LARGEx1",
"SBR" and "SBL" are not appeared but "SB" is appeared on the
Display.
The channel indication blinks while the test tone is being output.
SP MUTE
A B CLIP
L C SW R
LFE
SL SB SR
• If the speaker setting selects are OFF, the speaker level settings
are reset.
For "T.TONE MANUAL" selection, press the 5/∞ keys or
MULTI @/# keys each time to select the speaker channel.
If "T.TONE OFF" is selected, test tone is not output. Adjust
the volume level from each speaker by listening the selected
input source.
4 Press the MEMORY/ENTER key or the ENTER key to return to
the "SP LEVEL" display.
• The test tone is turned off and return to the main setup displays.
3
Input the distance to the speakers.
• Indicators appear only for the channels of the speakers selected
in step 1 .
1 Press the 5/∞ keys or MULTI @/# keys to select the "SP
DISTANCE" and press the MEMORY/ENTER key or the EN-
TER key.
2 Use the 5/∞ keys or MULTI @/# keys to select a unit in
distance and press the MEMORY/ENTER key or the ENTER
key.
1 UNIT meters
2 UNIT feet
3 RETURN
: Press the MEMORY/ENTER key or the ENTER
key to return to the "SP DISTANCE" display.
: Adjust the volume level from each
speaker by using test tone.
Test tone will be output from each
speaker in order.
by using test tone.
: Adjust the volume level from each
speaker without using test tone.
: Press the MEMORY/ENTER key or the
ENTER key to return to the "SP LEVEL"
display.
RIGHT
SL SBL SBR
SR
¢