Roland JUNO-X Reference Manual page 52

Q&A
06
Are Bluetooth earphones or headphones
supported?
No, they are not supported.
Operation
08
Why do the panel knobs and buttons work
sometimes and not at other times?
The parameters are different for each model, so there are cases in
which a controller has no parameter. Since the controllers without
a parameter differ between models, a controller might or might not
have an effect.
The parameter that is controlled by each knob or button will differ
depending on the model used by the tone that's assigned to the
current part (the currently selected part).
Ø "Correspondence Between Controllers and Parameters" (p. 27)
09
Is there a way to move quickly to the edit
screen for the parameter controlled by each
knob?
Yes.
1 .
Hold down the [SHIFT] button and turn the knob of
the parameter that you want to edit .
The settings screen for each knob appears.
Ø "Correspondence Between Controllers and Parameters" (p. 27)
10
Is there a way to move quickly to the settings
screen for the [SL1] and [SL2] sliders or the [S1],
[S2] and [S3] buttons?
Yes.
1 .
Hold down the [SHIFT] button and operate the slider
or button that you want to assign .
The assignment screen for the corresponding controller
appears.
11
Is there a way to check the current value of
a setting without affecting the state of the
sound?
Yes.
1 .
Hold down the [EXIT] button and operate the knob
that you want to check .
The current value of the setting is shown.
12
The part on/off button is lit, but I can't play the
sound of that part from the keyboard.
(PART/OSC ON [1]–[R] buttons, when the [PART/FUNC] button is lit up
yellow—at factory default)
This might be due the following reasons.
¹ The part might be assigned for arpeggio performance
¹ The I-ARPEGGIO ON/OFF button is ON, and the ARPEGGIO PART EDIT parameter
Switch is "ON. "
Ø "If the Keyboard Does Not Play Sound" (p. 21)
52
07
Can I specify a MIDI channel for each part?
Yes.
The MIDI channel is specified by the "Rx Ch" parameter in the SCENE
PART EDIT screen for each part.
13
Is there a way to move quickly to the TONE
(PARTIAL) edit screen?
Yes.
1 .
While holding down the [SHIFT] button, operate the
sliders for each waveform in the OSC section (square
wave, sawtooth wave, SUB and NOISE) .
The edit screen for the corresponding tone or partial appears.
* The screen contents may vary, depending on the model.
14
Can I change the models or categories that are
recalled by the [MODEL BANK] buttons [1]–
[16]?
Yes.
1 .
Hold down the [MODEL BANK] button and then press
the [1]–[16] buttons .
The model or category recalled by the [MODEL BANK] button
can be set for each bank.
* Up to eight can be set for each button (BANK).
2 .
Use the [ÇSELECTÉ] knob to move the cursor to
"Attr . "
3 .
Use the [- VALUE +] knob to select the model/
category/user .
4 .
Use the [ÇSELECTÉ] knob to select the model
number you want to change .
5 .
Use the [- VALUE +] knob to select a model name
(device name) or category name .
* You can register up to eight models or categories in one model bank.
* You can't mix and assign both a model and a category in a single model
bank.
6 .
If you want to save the setting, execute the System
Write operation .
6-1 .
Hold down the [SHIFT] button and press the [MENU] (WRITE)
button.
The WRITE MENU screen appears.
6-2 .
Use the [ÇSELECTÉ] knob to select "SYSTEM," and then press
the [ENTER] (INIT) button.
6-3 .
To execute, press the [ENTER] (INIT) button.