Toshiba Q9 Plus Bypass ASD Installation & Operation Manual page 68

S15 ASD
MODEL RANGE
Voltage Rating
POWER REQUIREMENTS
Input Tolerance
Output Frequency
CONTROL SPECIFICATIONS
Control Method
Voltage Regulation
V/Hz Control
PWM Carrier Frequency
Frequency Setting
Frequency Precision
Speed Regulation
Main Protective Functions
Retry
Restart
Overload Current Rating
CONTROL INTERFACE
Digital Input
Digital Output
Analog Input
Analog Output
Communication Ports
ELECTRONIC OPERATOR INTERFACE (EOI)
Display
LED Indicators
Keys
Monitoring
CONSTRUCTION
Enclosure
Power Cables
Cooling
Standards & Compliances
AMBIENT CONDITIONS
Ambient Temperature
Altitude
Humidity
Installation
TOSHIBA INDUSTRIAL PRODUCTS:
• Adjustable Speed Drives
• Motors
• Motor Controls
• Instrumentation & PLCs
• Uninterruptible Power Systems
© 2012 Toshiba International Corporation • Industrial Division • 13131 West Little York Road • Houston, Texas 77041 USA • Tel +713-466-0277 US 1-800-231-1412 • Rev. 120411
1/4 HP to 3 HP
Single-Phase 230 VAC
Voltage: ±10%; Frequency: ±5%
0.1 to 500 Hz
Sinusodial Pulse Width Modulation (PWM); Flux-Field Current Vector Control; Set Point Control (PID)
Main Circuit Voltage Feedback Control: Automatic, Fixed, & Off
V/f Constant, Variable Torque, Automatic Torque Boost, Vector Control, PM Motor Control, 5-point V/F Custom Setting, & Auto-Tuning
Adjustable 2 to 16 kHz (For Drive Specific Information Consult Factory)
Rotary Encoder Integrated into EOI, 0 to 10 VDC, ±10VDC, 4 to 20 mA, Digital Input, Binary Input, & Motorized Potentiometer Input
Analog Input ±0.5% of Maximum Output Frequency; Discrete/Communications Input ±0.01% of Maximum Output Frequency
Open Loop: Up to 0.1%, 60:1 Speed Range
Stall Prevention, Current Limit, Over-Current, Output Short Circuit, Over-Voltage, Over-Voltage Limit, Undervoltage, Ground Fault
Detection, Input Phase Failure, Output Phase Failure, Overload Protection by Electronic Thermal Function, Armature Over-Current
at Start-Up, Load Side Over-Current at Start-Up, Over-Torque, Undercurrent, Overheating, Cumulative Operation Time, Life Alarm,
Emergency Stop, & Various Pre-alarms
User-Set Number of Retries for Automatic System Restart After Trip
Able to Smoothly Catch Freewheeling Motor (Bidirectional)
110% Continuous; 150% for 1 Minute
6 Discrete Input Terminals Programmable to 110 Functions (May Be Increased Using Optional Hardware)
3 Discrete Output Terminals Programmable to 150 Functions; 1 Form-A Contact, 1 Form-C Contact, & 1 Open Collector Output
3 Programmable: One 4 to 20 mA Input, One 0 to 10 VDC Input, & One ±10 VDC Input
1 Programmable: 4 to 20 mA or 0 to 10 VDC
RS485 Port (TSB or MODBUS RTU Protocol)
4x20 Graphical Full-English LCD Back-Lit Display for Programming, Monitoring, & Diagnostics
Run (Red)/Stop (Green), Hand (Green), & DC Bus Charge Indicator (Red)
Run, Prg, Mon, Status, %, Hz, Stop, Mode, & Easy Key; Rotary Encoder for Parameter Navigation, Settings, & Control
Frequency Command Screen; Multiple Parameters Displayed: Output Frequency, Forward/Reverse Run, Output Current, Input Volt-
age (DC Detection), Output Voltage, Torque, Inverter Load Factor, Motor Load Factor, Braking Resistor Load Factor, Input Power,
Output Power, Input Terminal status, Output Terminal Status, Overload/Regional Setting, PID Feedback Value, Stator Frequency,
Parts Replacement Alarm, Cumulative Operation Time, & Past Trips
RAL 7016 (Anthracite Gray); IP20; Wall-Mount; Front-Access Only
Bottom Access for Input/Motor Cables
Self-Cooling/ Forced Air-Cooled
UL Listed in US & Canada, CSA, & CE
0 to 60°C (Note: See Manual for Details, Ambient Temperatures Above 50°C May Require a De-Rate)
3300 ft. Above Sea Level (Up to 10,000 ft. with Derate)
95% Maximum (Non-Condensing)
Indoors; No Direct Sunlight; Protects from Corrosive Gas/Explosive Gas/Flammable Gas/Oil Mist/Dust; Vibration of Less Than
5.9 m/s 2 (10 to 55 Hz)
1/2 HP to 20 HP
Three-Phase 230 VAC
www.toshiba.com/ind
1/2 HP to 20 HP
Three-Phase 460 VAC