Toshiba Q9 Plus Bypass ASD Installation & Operation Manual page 64

Q9 PLUS ASD
MODEL RANGE
Voltage Rating
Frame Size
HP Rating
Input Voltage Tolerance
Voltage Regulation
PWM Carrier Frequency
Control System
V/f Pattern
Overload Current Rating
Frequency Setting
Frequency Precision
Output Frequency Range
Speed Regulation
Set Point Control
Load Balancing
Retry
Restart
Sleep Timer
Enclosure Type
Standards/Compliances
INPUT/OUTPUT
Discrete Input Terminals
Analog Inputs
Discrete Output Contacts
Analog Outputs
Communication Port
Power Terminals
SAFETY FEATURES
Start & Stop Points
Damper-Permissive Circuit
Selectable Fire-Speeds
ELECTRONIC OPERATOR INTERFACE (EOI)
LCD (Liquid Crystal Display)
LED (Light Emitting Diode)
LED Indicators
Keys
Rotary Encoder
Monitoring
Display Units
Set-Point Units
TOSHIBA MOTORS & DRIVES DIVISION
• Adjustable Speed Drives
• Motors
• Motor Controls
© 2015 Toshiba International Corporation • Motors & Drives Division • 13131 West Little York Road • Houston, Texas 77041 USA • Tel +713-466-0277 US 1-800-231-1412 • Rev. 150120
1 to 125 HP
200 to 240 VAC
2 to 10
1 to 125 HP
+ - 10%
Main Circuit Voltage Feedback Control: Automatic, Fixed, & Off
Adjustable 1 to 16 kHz (Drive-Specific, Consult Factory)
Sinusoidal PWM with VLP
Constant Torque, Voltage Decrease Curve, Automatic Torque Boost, Sensorless Vector Control, 5-Point V/f Custom Curve, PM Drive, & PG
Feedback Vector Control
100% Continuous; 110% for One Minute
Rotary Encoder Integrated into EOI, 0 to 10 VDC, ±10 VDC, 0 to 20 mA, & Discrete Input
Analog Input 0.2% of Maximum Output Frequency; Discrete/Communications Input 0.01% of Maximum Output Frequency
0 to 299 Hz
Closed Loop (Up to 0.01%; 1000:1 Speed Range); Open Loop (Up to 0.1%; 60:1 Speed Range)
Selectable Between VLP/PID; Proportional Gain, Integral Gain, Feedback Settings, Upper/Lower Deviation Limits, Feedback Source Delay
Filter, & Feedback Settings Differential Gain
Capable of Balancing Load on Pumps Operated by Q9 Plus Drives on Common Header
User-Set Number of Retries for Automatic System Restart After Trip
Able to Smoothly Catch Freewheeling Motor (Bidirectional)
Shuts Off Fan After Running at VLP Minimum for User-Specified Time
IP20/IP00 (Rating-Dependent), NEMA 1 Kit Available
UL Listed & American Recovery & Reinvestment Act (ARRA) Compliant
Eight Discrete Input Terminals Programmable to 57 Functions; May Be Increased Using Optional Hardware
Three: One 0 to 20 mA or 0 to 10 VDC Isolated Input, One 0 To 10 VDC Input, & One ±10 VDC Input
Three Programmable To 83 Functions; Two Form-A Contacts & One Form-C Contact
Two: One Programmable 4 to 20 mA or 0 to 10 VDC & One 4 to 20 mA Output
Half/Full Duplex RS485; Integrated Protocols: BACnet, Modbus, & Toshiba TSB
Input (L1, L2, L3), Output (T1, T2, T3), DCL (PO, PA), DBR (PA, PB), & DC BUS (PA, PC)
Determine Start/Stop Based On User-Set Values, Transducer Feedback Signal, & Programmable Discrete Input Terminal;
Work with Delay Timer to Ensure ASD Does Not Start/Stop Too Frequently Due to Unstable/Fluctuating Input Signal
Protects Drive from Over-Pressuring the System
Two Fire-Speeds; Force Drive to Run at Preset Speeds
Full-English Backlit Display
Seven-Segment Display
Run (Red)/Stop (Green), Hand (Green), & DC Bus Charge Indicator (Red)
Hand/Auto, ESC, Run, Mode, & Stop/Reset
Encoder with Integrated Enter Key to View/Change Parameter Settings
Frequency Command Screen; Allows Two User-Selected Monitored Items to be Displayed; Selectable from: Output Current, DC Voltage,
Output Voltage, Run Time, Comp. Frequency, VLP, Motor Overload, Motor Load, ASD Load, Input Power, Output Power, RR Input, V/I Input,
RX Input, RX2 Input, AM/FM Output
Completely Configurable Along with Scaling Factor Multiplier; Display Selectable Between Amps (A) or Percentage of FLA (%); Voltage
Display Selectable Between Volts (V) or Percentage of Volts (%)
Selectable Between PSI, GPM, CFM, Inches of Water Column (inH2O), or Feet of Water Column (ftWC)
1 to 400 HP
380 to 480 VAC
2 to 13
1 to 400 HP
www.toshiba.com/tic