Table of Contents
Advertisement
6.
Push the arrow buttons to select the distance,
measured in m.
7.
Push the OK button.
8.
Use the arrow buttons to select the percentage of
the cutting time the product must cut the area. The
percentage is equal to the percentage of the area
in relation to the complete work area.
a)
Measure the area.
b)
Divide the measured area with the total work
area.
c)
Convert the result to percentage.
Note:
The sum of Area 1-3 must be 100% or
less. If the sum is less than 100%, the product
sometimes straddles the guide wire and starts to
mow at the charging station.
9.
Push the BACK button.
To set the System Passage Mowing function
Note:
To prevent that the grass in the narrow
passage is worn, Husqvarna recommends to set a low
Systematic Passage Mowing .
percentage for the
To get access to the menu in the
1.
Do steps 1–3 in
display of the product on page 21 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area 1-3 .
3.
Use the arrow buttons to select the area.
4.
Push the OK button.
5.
Measure the distance from the charging station
to the beginning of the narrow passage. Measure
along the guide wire. Refer to
distance from the charging station on page 25 .
Note:
Make sure that the distance to the
Systematic Passage Mowing is set inside the
narrow passage.
6.
Push the arrow buttons to select the distance.
7.
Push the OK button.
8.
Use the arrow buttons to select the % of the
cutting time that the product must start the narrow
passage cutting.
9.
Use the arrow buttons and the OK button to select
More > Systematic Passage Mowing .
10. Push the OK button to enable
Mowing .
11. Push the BACK button.
To do a test of the Lawn Coverage function
1.
Put the product in the charging station.
2.
Do step 1-3 in
To get access to the menu in the
display of the product on page 21 .
1462 - 007 - 14.03.2022
3.
4.
5.
6.
7.
To measure the distance from the charging station
1.
2.
3.
4.
5.
6.
7.
8.
To disable or enable the Lawn Coverage function
Settings > Lawn
Disable or enable the
area.
1.
2.
To measure the
3.
4.
To reset the Lawn Coverage settings
You can reset the
and use the factory setting.
1.
2.
3.
3.12.7.2 Methods for the product to find the charging
Systematic Passage
station
The product has 3 search methods to find the charging
station:
•
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area > More > Test .
Push the OK button.
Push the START button.
Close the hatch.
Make sure the product can find the area.
Put the product in the charging station.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 21 .
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area > How far?
Use the arrow buttons to set 500 m / 500 yd as a
distance.
Push the OK button.
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area > More > Test .
Push the OK button.
Push the STOP button when the product is at
the distance you select to measure. The distance
shows in the display.
Lawn Coverage function for each
To get access to the menu in the
Do steps 1–3 in
display of the product on page 21 .
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area > Disable .
Push the OK button.
Push the BACK button.
Lawn Coverage settings for each area
Do steps 1–3 in
To get access to the menu in the
display of the product on page 21 .
Use the arrow buttons and the OK button to
move through the menu structure
Coverage > Area > More > Reset .
Push the OK button.
Irregular - The product operates in the work area
until it finds the signal of the charging station.
Settings > Lawn
Settings > Lawn
Settings > Lawn
Settings > Lawn
Settings > Lawn
Installation - 25
Advertisement
Table of Contents
