Maintenance - Chicco BABY HUG 4 IN 1 Manual

CLEANING
Clean the plastic parts with a soft damp cloth. Never use
abrasive detergents or solvents. If the highchair comes
into contact with water, dry the metal parts to prevent
the formation of rust.

MAINTENANCE

• This product requires periodical maintenance.
• Cleaning and maintenance operations must only be
carried out by an adult.
• Periodically check the product for broken, damaged or
missing parts: do not use it in this case.
• To avoid friction that may compromise the correct
functioning of the product, ensure that all the moving
plastic parts located along the metal frame are free of
dust, dirt and sand.
• If necessary, lubricate the moving parts with dry sili-
cone lubricant.
• Store the product in a dry place.
COMPONENTS
The product is completely disassembled when pur-
chased; check that all of the components listed below
are present. If any part is missing contact ARTSANA's
CUSTOMER SERVICES.
The product and all of its components must always be
assembled by an adult.
A - Height adjustable pedestal frame
A1 - 4 wheels with brakes
B - Seat frame
C - Seat structure
D - Tubular seat frame
E - Fabric (with shoulder straps)
F - Booster cushion
G - Toybar
G1 - Light / sound game buttons
G2 - 3 soft toys
I - Upper fabric zips
L - Plastic clips
M - Height adjustment pedal
N - Backrest recline lever
ASSEMBLY
The product is not assembled when purchased. To use
it, carry out the following assembly operations:
1. The first thing to do is assemble the "A1" wheels on
height adjustable base frame "A". To do this place the
frame on a rug or soft surface so as not to damage the
floor or frame. Assemble the 4 "A1" wheels inserting
the pins in the 4 holes under height adjustable base
frame "A" as shown in figure 1.
WARNING: Fully insert the wheel pin into the hole in
the base. At this point the base can be rested on the
floor.
2. Insert the fasteners of seat frame "B" into the respec-
tive tubes on seat structure "C" until they click into
place (Fig. 2).
3. Assemble the seat (seat frame "B" + seat structure
"C") on the base: insert the two tubes on base "A"
into the corresponding holes on seat frame "B" until
they click into place (Fig. 3).
WARNING: The backrest must face the height adjust-
ment pedal (I) as shown in Fig. 3a.
4. Insert tube "D" into the corresponding holes on seat
frame "B" until they click into place (Fig. 4).
5. To assemble fabric "E" line up the holes on the fabric
with the restraint system installed on seat structure
"C". Pass the two lateral arms of seat frame "B" through
the side fabric holes (FIG. 5), insert the pins of the
arms into the holes on either side of the backrest (FIG.
5a) until they click into place.
WARNING: Check that both arms are assembled cor-
rectly.
6. Attach fabric "E" using the two perimeter zips above
seat frame "B" (Fig. 6).
7. Pass the crotch strap and waist straps on seat struc-
ture "C" through the holes of fabric "E" (Fig. 7-7a-7b-
7c).
8. Attach the fabric (E) to the bottom of seat structure
"C", making sure to insert all of the plastic clips in the
right slots (Fig. 8-8a).
BOOSTER CUSHION
9. Reducer cushion "F" is ideal from birth and can be
used or removed as necessary. To attach it to the
seat, place it on the fabric, pass the crotch strap and
waste straps through the holes in booster cushion "F"
(reclined cradle mode), (Fig. 9). In highchair mode it
is also necessary to pass the shoulder straps through
the holes of the booster cushion (Fig. 9a).
TOYBAR
10. The toys can be attached to the toybar by passing the
straps through the plastic openings on the bar (Fig.
10) and fastening the velcro.
11. Assemble the toybar (with the light positioned to-
wards backrest recline lever "N") inserting the pins of
the bar into the holes on seat frame "B" until it clicks
into place (Fig. 11).
12. To incline the toybar in the three possible positions
press the side buttons (Fig. 12).
13. To remove the toybar press the buttons on the inside
of the bar support and pull upwards (Fig. 13).
WARNING: Always check that the toybar is properly
fastened before using it.
WARNING: To prevent possible injury by entaglement,
remove this toy when the child starts trying to get up
on its hands and knees in a crowling position.
HEIGHT ADJUSTMENT
14. Once assembled, the product can be adjusted to
various heights in all configurations. To adjust its
height, hold down height adjustment pedal "M" (Fig.
14) and lift or lower the seat to the desired height.
ADJUSTING THE BACKREST
15. The backrest can be adjusted to four different posi-
tions. To do this, push down on backrest recline lever
"N" (Fig. 15).
10