Care And Maintenance - Chicco Rhythm'n'Sound Instructions For Use Manual

or walls.
• If the reclined cradle is left exposed
to direct sunlight for an extended
period of time, allow it to cool down
before placing your child inside.
• Prolonged exposure to direct sun-
light can cause the fabric to fade.
• Keep the product out of reach of
children when it is not being used.

CARE AND MAINTENANCE

The fabric on the reclined cradle can be removed, see the
chapter on "REMOVING THE FABRIC". Periodically wipe the
plastic parts clean with a soft damp cloth. After possible
contact with water, dry the metal parts in order to avoid the
formation of rust. Do not use solvents or abrasive products.
• This product requires periodical maintenance.
• Cleaning and maintenance operations must only be car-
ried out by an adult.
• Check that the fabric, stitching and buttons are in good
condition each time you wash it.
• Please refer to the care label for instructions on washing
the product:
Hand wash
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Do not twist or wring
line drying
LIST OF COMPONENTS
A – Base
A1 - Recline button
A2 - Close button
A3 - Button to lock/unlock side to side movement
B - Feet (x2)
B1 - Screws for fastening feet (x2)
C - Seat fabric with backrest frame
D - Safety harness
E - Buckle
F - Prongs
G - Ring for adjusting the safety harness
H - Snap buttons
I - Seat fabric buttonhole
J - Hook tab for fabric buttonhole
K - USB power cable
L - Control panel for side to side movement / music
L1 - On/off button for side to side movement
L2 - On/off button for music
L3 - Button for adjusting volume and changing tunes
L4 - Timer button
L5 - Power supply connector
L6 - Battery compartment cover
FIRST ASSEMBLY OF THE RECLINED CRADLE
1. Insert the feet "B" in the base "A" (Fig. 1), tighten the screws
"B1" in their holes (Fig. 2) and open the base "A" of the
reclined cradle by pulling up on the rods until you hear
a click (Fig. 3).
2. Lift the fabric component of the backrest frame "C" to un-
cover the tubes (Fig. 4), insert the two tubes in the rods
located on the base "A" (Fig. 5) making sure they go all the
way down (Fig. 6).
3. Then, lower the fabric (Fig. 7). Wrap the fabric around the
frame, fasten the 2 snap buttons "H" (Fig. 8), finish assem-
bling the fabric by wrapping fabric buttonhole "I" around
the hook tab "J" (Fig. 9).
ADJUSTING THE BACKREST
4. To adjust the inclination of the backrest from a higher to
a less inclined position, pull out on the recline button "A1"
(Fig. 10). To switch from a less inclined position to a high-
er position, simply pull up on the backrest (Fig. 11). This
operation may also be carried out with the child sitting
in the reclined cradle. In this case it can be more difficult.
WARNING: Always guide the backrest with the fingers
when adjusting the reclining.
WARNING: Always check that the backrest is properly
locked before use.
USING THE SAFETY HARNESS
5. The safety harness should already by fitted when it comes
to using the reclined cradle for the first time. (Fig. 12).
To release them, press the central button on the buckle "E"
(Fig. 13) and extract the two prongs "F" (Fig. 14). The reclined
cradle is ready for the child.
WARNING: When using the product, always fasten the
5-point safety harness and check that it is tight enough and
properly fastened.
6. To adjust the length and tension of the safety harness,
keep one end of the buckle blocked while pulling on the
belt and sliding it into the ring "G" (Fig. 15).
FIXED POSITION OR SIDE TO SIDE MOVEMENT
The reclined cradle is equipped with a motorised mecha-
nism that allows it to move from side to side.
7. The reclined cradle can be used in fixed or motorised side
to side movement mode:
• Fixed mode: push down on the side to side movement
lock button "A3" (Fig. 16);
• Side to side movement function: release the side to
side lock button "A3" by pulling up and use the side to side
movement on/off button "L1" to activate the movement.
The side to side movement function can be set to either
of 2 different modes using the timer button "L4", activat-
ing the function for a maximum of 30 minutes ("L1" power
light fixed) or 10 minutes ("L1" power light blinking).
SOUND PANEL
The reclined cradle includes a MUSIC PANEL that can be
activated using the buttons located on the side (Fig. 17).
8. To play music simply press the music on button "L2" (Fig.
18)
9. To switch between tunes press the "L3" button once (Fig.
14