Integra DTR-7 Instruction Manual page 47

Enjoying Music and Movies in the Sub-room
MULTI SOURCE indicator
DIMMER
STANDBY/ON
MULTI SOURCE
ST ANDBY MUL TI SOURCE
POWER
ON OFF
A SPEAKERS B
DISPLAY DIRECT
PHONES MUL TI CH INPUT
DVD VIDEO-1 VIDEO-2 VIDEO-3
REC OUT/MULTI SOURCE
1. POWER ON
2. Input Selector
When the system is mounted in a rack:
DIGITAL INPUT R L R L V S
AMP IN
OUT
FRONT
COAXIAL ANTENNA
1 VIDEO-1
PRE OUT
IN
FRONT
COAXIAL AM
2
SUB
WOOFER
OUT
OPTICAL
1
CENTER VIDEO-2
IN
SURROUND
OPTICAL
2 FM
75
VIDEO-3
FRONT IN
OPTICAL
SUB
DVD
WOOFER
DIGITAL OUTPUT IN
CENTER AV RECEIVER
MODEL NO. DTR-7
SURROUND
(REC) MONITOR
MULTI CHANNEL
OUT OUT
INPUT
R L
TAPE
MULTI SOURCE
IN OUT
CD
(PLAY)
GND
VIDEO
PHONO
S VIDEO
OSD SELECTOR
R L R L
LOCAL REMOTE REMOTE
CONTROL
1
LOCAL REMOTE
Mini Plug cable
SMART SCAN Controller
MASTER VOLUME
FM MUTE/ CHARACTER/ SP/SYS AUDIO BASS/
MODE MEMORY SETUP ADJUSTMENT TREBLE
DOWN TUNING UP
MODE
PRESET/MODE ADJ
PUSH TO ENTER
LISTENING MODE
REC OUT / DIGITAL/
STEREO /DTS THX DSP MULTI SOURCE ANALOG CH LEVEL
SURROUND MODE
VIDEO4 (MONO)
VIDEO-4 TAPE FM AM PHONO C D
S VIDEO VIDEO L AUDIO R
DTR - 7 by
DTR-7/DTR-6
SURROUND SPEAKERS FRONT SPEAKERS A
R L R L
CENTER
SPEAKER
CAUTION: SPEAKER IMPEDANCE
6 OHMS MIN. / SPEAKER
R L
AC OUTLETS
FRONT SPEAKERS B AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
AC INLET
Power
HB-100
supply
Connecting block
120V AC
(unswitched)
In the rack
To control the system in the sub-room
1. Press the POWER ON button on the remote controller.
The MULTI SOURCE indicator located below the STNDBY/
ON button on the receiver will light to indicate that the system
enters the Multi-Source mode.
Note:
If you operate the system in the sub-room while a recording is going on in
the main-room, the source of the recording switches to the source which you
are playing in the main room. Be careful when you are recording a different
source from the one that you are playing.
2. Press the appropiate Input Selector button on the remote
controller to select your desired source and start operating
it.
3. Adjust the volume on the power amplifier to the desired
level.
To control the system using the main unit
(e.g. when no remote controller is available):
1. Press the REC OUT/MULTI SOURCE button on the system
to make sure the MULTI SOURCE indicator flashes in the
display window.
2. Making sure that the indicator flashes, select a source by us-
ing the Smart Scan Controller.
Adjust the volume in the sub-room.
Notes:
• In the sub-room, you can only play the source in the 2-Channel mode.
You cannot play the source in the Multi-Channel mode or the Surround
mode.
• If you press the REC OUT/MULTI SOURCE button in the main room
while you are playing the source in the Multi Source mode in the sub-
room, the Multi Source function will be deactivated and the source will
be inaudible in the sub-room.
• Please note that some third-party multi-room system components may
not be fully compatible with the Onkyo multi-room system components.
To enable remote operation when the receiver is mounted in a rack
which will not permit infrared beams to pass, install the remote sen-
sor at a location outside of the rack where the infrared beams from
the controller can reach.
1. Connect the LOCAL jack (on the rear of the receiver) to the
connecting block.
2. Install the remote sensor at a location where it can detect the
infrared beams from the remote controller. Then, connect
the remote sensor to the connecting block.
2
Remote sensor HR-600
Outside of the rack
Remote contoroller
47