Listening To Radio Broadcasts; Using The Tuner; Tuning Into A Radio Station - Integra DTR-10.5 Instruction Manual

Listening to Radio Broadcasts

Using the Tuner

One of the features of the DTR-10.5 that is most
frequently used is its ability to play FM and AM broadcast
radio stations. The DTR-10.5 provides a number of
listening modes perfect for listening to the radio and
getting the most out of your audio system. Also, by
presetting radio stations that you listen to frequently, you
can select them easily by pressing the [CH/Disc +/–]
button on the remote controller.
Setting the AM Tuning Interval
For the Australian model, you have to adjust the "AM
Frequency Step" setting according to your area.
Use the Setup menu to adjust the "AM Frequency Step"
setting.
To perform this setting, go to "Hardware Setup" → "AM
Frequency Setup" → "Frequency Step," and select "9 kHz"
or "10 kHz." For details on this setting, see page 87.

Tuning into a Radio Station

Standby/On
Standby
Display Tape 1
Rec/ Zone 3 Red ) (
Main Blue ( )
Zone 2 Green ( )
DVD Video 1 Video 2
Pure Audio
Listening Audio
Mode Selector Tone Zone 2 Select/ Preset
Phones
Tuning
Mode Memory Dimmer Level
Clear
Push To Enter
Tuning Mode Select/Preset
Tuning into a Radio Station Automatically
(automatic tuning)
1 Press the [Tuner] input source but-
ton.
Tuner
Each time you press the [Tuner] button,
the input source changes between AM
and FM.
2 Press the [Tuning Mode] button to
Tuning
Mode Memory
turn on the "AUTO" indication.
3 Turn the [Control/Tuning] dial
either clockwise or
Control / Tuning
counterclockwise. This starts
tuning automatically.
The tuner stops automatically where it
tunes into a station.
When you tune into a radio station,
TUNED
display. If you tune into an FM station in
stereo, then "FM STEREO" appears.
62
Tuner
Master Volume
Tape 2 Tuner Phono C D Net Audio
Video 3 Video 4 Video 5 Video 6 Video 7
Open
Setup Control / Tuning Rec/ Zone 3 Video 7 Input
Digital S Video Video L Audio R
Exit Level
Push To Enter
indicator appears in the
Band
Frequency
When the FM stereo broadcast contains much noise:
Press the [Tuning Mode] button to switch to the manual
tuning mode. The "AUTO" indication disappears and the
tuner turns into the monaural mode. In the monaural
mode, the noise will be reduced and the broadcast be
easier to hear.
Tuning into a Radio Station Manually
(manual tuning)
1
Press the [Tuner] input source
button.
Tuner
Each time you press the [Tuner] button,
the input source changes between AM and
FM.
2
Press the [Tuning Mode] button to
turn off the "AUTO" indication.
Tuning
Mode Memory
3 Turn the [Control/Tuning] dial
either clockwise or
Control / Tuning
counterclockwise to tune your
station.
Turning counterclockwise decreases the
frequency, and turning clockwise
increases the frequency.
• The tuner frequency changes in 200 kHz (50 kHz)
increments for FM and 10 kHz (or 9 kHz) increments
for AM.
• When you tune into an FM station manually, the tuner
turns into monaural mode. If you want to listen to the FM
station in stereo, press the [Tuning Mode] button.
Specifying Radio Stations by Frequency
To select a radio station by
Remote controller
entering its frequency, press
Clear
#
the remote controller's [Direct
Direct Tuning
Tuning] button, and then use
the number buttons to enter
the frequency.
1 2 3
@.-'/ ABC DEF
4 5 6
GHI JKL MNO
7 8 9
PQRS TUV WXYZ
+ 10
0
--/---