Table of Contents
Advertisement
Available languages
Available languages
RU LES FOR SAFE DRIVIN G
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
W ARN IN G!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
ASSISTAN CE SERVICE
offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted. S ee
the pag e on spare parts to find out how to identify the
serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
S ATIS FACTION QUES TIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY IN ST RU CT ION S
W ARN IN G
THE VEHICLE MUS T BE AS S EMBLED BY ADUL TS .
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE P ACKAGING.
ALL THE NECES S AR Y S CREWS AND S MALL
COMPONENTS ARE S TORED IN A BAG INS IDE
THE P ACKAGING.
THE BATTER Y MAY ALREADY BE INS TALLED.
1 • Attach one of the hub covers (with a square hole
in the middle) to one of the two wheels with a
square hole.
2 • Turn the wheel over and apply the driver shown
in the detail illustration (with the hexagonal end),
aligning the 4 pins with the holes in the wheel.
3 • Insert a self-locking cap with a square inside on
the conical bushing, as shown in the drawing.
• Put the square axle into the hole in the self-
locking cap and use the hammer to anchor the
two components in place.
4 • Put the axle into the wheel you have assembled,
on the hub cover side.
5 • Insert the axle and wheel into the hole in the
gearmotor on the back of the product.
• Align the pentagon in the gearmotor with the
pentagon of the driver. Push all the way in to set
in place.
6 • J oin the remaining hub cover with the square
hole in the middle to the other wheel with the
square hole.
• Turn the wheel over and apply the driver shown
in the detail illustration (with the hexagonal end),
aligning the 4 pins with the holes in the wheel.
7 • Fit the wheel onto the axle, pushing the (round) end
of the driver all the way into the hole in the body .
8 • Insert a self-locking cap with a square inside onto
the black press-stud.
9 • Place the product on its left side. Put the conical
bushing in place under the wheel resting on the
work surface, as shown in the drawing. Rest the
black press-stud on the upper wheel and use a
hammer to fix the wheel in place.
10 • Insert the prong at the front of the body until it
snaps onto the pin at the bottom of the
template, as shown in the drawing (see detail in
next photo).
11 • The peg on the prong must fit into the curved
opening, as shown in the drawing.
12 • Insert the nut provided into its housing under
the front mud flap. Insert the threaded pin from
the opposite side.
13 • S crew in the threaded pin to anchor the prong in
place under the body, making sure that the nut
does not come out of its seat.
14 • Press the template into place, hooking the lower
part onto the prong with the two tongues.
15 • Press the handlebar onto the three holes in the
prong.
16 • S ecure the bumper to the frame using the two
screws provided.
17 • Fit the two hand grips onto the handlebar until
the tongues click into place (see detail).
18 • Take the bell components out of their box.
19 • Fit the spring and then the bell onto the
handlebar (follow the instructions on the
illustrated instruction leaflet). Put the cover in
place and fix the entire assembly in place with
the ring nut.
20 • Apply the remaining two hub covers to the
remaining wheel (the one with the round hole).
21 • Insert a self-locking cap with a circle inside on
the conical bushing, as shown in the drawing.
• Put the remaining axle into the hole in the self-
locking cap and use the hammer to anchor the
two components in place.
22 • Insert the wheel between the tubes of the front
prong, aligning all the holes. Insert the axle as
shown in the drawing.
23 • Insert a self-locking cap with a circle inside onto
the black press-stud.
• Place the product on its side with the part of the
axle with the cap facing down. Position the
conical bushing as shown in the drawing. Rest the
black press-stud on the other side and use a
hammer to fix the wheel in place.
24 • Connect the terminals of the electrical system
and the battery.
25 • Put the saddle in position, inserting the tongue in
the body as shown in the figure. Push the
anchoring pin all the way into the hole at the rear.
26 • Turn the anchoring pin to position B to lock the
CONS UMER
saddle in place.
27 • The vehicle is now ready for use. Press the
accelerator pedal while keeping both hands on
the handlebar.
ASSEMBLY
REPLACIN G T H E BAT T ERY
PLEAS E NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUS TRATIVE PURPOS ES ONL Y. YOUR
BATTER Y MAY BE DIFFERENT FROM THE MODEL
S HOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DES CRIBED.
28 • Turn the saddle anchoring pin to position A to
release it. Lift the seat.
29 • Disconnect the terminal of the electrical system
from that of the battery.
30 • Cut the strap.
31 • Replace the dead battery with a new battery
which has been charged for at least 14 hours.
NOTE : replacement batteries are only available
with a power of 6V/6, 6Ah. This will not affect
the operation of the vehicle.
32 • Plug in the electrical system again. Put the seat
back and turn the anchoring pin to position B.
CH ARGIN G T H E BAT T ERY
WARNING: BATTER Y CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL S YS TEM
MUS T BE CARRIED OUT BY ADUL TS .
THE BATTER Y CAN ALS O BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
33 • Disconnect the electrical system terminal (A)
from that of the battery terminal (B), pushing it
sideways.
34 • Plug the battery charger terminal into a wall
outlet following the instructions enclosed.
Connect terminal B to the battery charger
terminal C.
35 • Once charging is complete, unplug the charger
from the wall outlet, then unplug terminal C
from terminal B.
36 • Insert terminal B all the way into terminal A,
pushing until it clicks. Once completed, always
remember to close and secure the saddle.
Advertisement
Table of Contents
