Table of Contents
Advertisement
Product features and decoration may vary from the picture above.
JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler Corporation and are used under license.
©DaimlerChrysler Corporation. Fisher-Price, Power Wheels by Fisher-Price, BARBIE, Beach Ranger,
Power Lock, and Power Stick are U.S. trademarks of Mattel, Inc.
Jeep
®
Owner's Manual
with Assembly Instructions
Please read this manual and save it with your original sales receipt.
For Model 78478
Tools needed for assembly: Phillips Screwdriver, Hammer, and Safety Scissors (not included).
Use only with a Power Wheels
®
12 Volt Battery with Built-in Thermal Fuse
and Power Wheels
®
12 Volt Charger (both included).
Requires four "AA" (LR6) alkaline batteries (not included) for Lights and Siren.
Advertisement
Table of Contents
Related Manuals for Power Wheels BARBIE KEEP BEACH RANGER 78478
Summary of Contents for Power Wheels BARBIE KEEP BEACH RANGER 78478
- Page 1 Product features and decoration may vary from the picture above. JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler Corporation and are used under license. ©DaimlerChrysler Corporation. Fisher-Price, Power Wheels by Fisher-Price, BARBIE, Beach Ranger, Power Lock, and Power Stick are U.S. trademarks of Mattel, Inc.
-
Page 2: Table Of Contents
Important Information ..............2 Warnings and Cautions . -
Page 3: Warnings And Cautions
ELECTRICAL HAZARD • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. -
Page 4: Parts
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. - Page 5 Parts Rear Bumper Knob Plate Seat Brush Guard Cord Retainer Dash Dash Knob – 2 Steering Column Steering Wheel Hood Latch – 2 Steering Wheel Cap Hood Brushguard Spacer Tube – 2 Key Assembly Gas Cap...
- Page 6 Parts Water Jug Holder Windshield Frame - Front Water Jug Windshield Hinge Pin – 2 Windshield Bracket – 2 Windshield Frame - Back Sport Bar Sport Bar Bracket Set Sport Bar Support - 2 Left Sidepipe Canopy Right Sidepipe Part Not Shown: Label Sheet...
- Page 7 Lights and Siren Unit These components are found in the Lights and Siren Unit. * #6 Washer and #6 x " Screw shown actual size. #8 x 4" Screw – 2 #8 x 1 " Screw – 10 " x "...
-
Page 8: Parts Diagram
Note: (Water Jug Holder) and (Water Jug) shown assembled to right side of vehicle body for clarity. Actual assembly is to left (driver) side of vehicle. Parts Diagram... - Page 9 Part Vehicle Body Steering Column .354 Cap Nut Retainer Hood Latch 12 Volt Battery Battery Clamp Unit #8 x 4" Screw Taillight Lens Taillight Housing #8 x 1" Screw Gas Cap Dash #10 x 1" Screw #10 x " Screw Windshield Hinge Pin Knob Plate Dash Knob...
-
Page 10: Battery Charging
ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. -
Page 11: Assembly
Battery Charging Battery • Plug the charger connector into the battery • Plug the charger into a standard 120 volt wall outlet Note: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. •... - Page 12 • Turn the vehicle body upright. • Gently bend the tab on one of the sidepipes under the vehicle body. • Insert a #8 x " screw through the hole in the vehicle body floor and into the tab. • Tighten the screw with a Phillips screwdriver. Do not over-tighten.
- Page 13 Assembly 13• Insert 7 K ey Assembly • Insert snap dash microphone knobs • cord into though knob plate hole HEAT COOL • A p p l y l a b e l s t o t h e d a s h a s i n d i c a t e d i n t h e i l l u s t r a t i o n .
- Page 14 End of Steering Column Cap Nut Bottom View • Insert the end of the steering column through the hole in the steering rod. • Fit a cap nut onto the end of the steering column. • While supporting the steering column, tap the cap nut with a hammer to secure it on the steering column.
- Page 15 Grille Slot • Fit the lens tabs on the back of a lens assembly into the headlight slots in the grille. • Press firmly to snap the lens assembly into the grille. • Repeat this procedure to snap the other lens assembly into the grille.
- Page 16 Windshield Brackets • Fit the screw pegs on the windshield brackets into the holes in the top surface of the dash. Press firmly to fit the lip on each windshield bracket into the slot in the top of the dash. •...
- Page 17 Lights and Siren Unit 1.5V x 4 “AA” (LR6) Shown Actual Size • Locate the battery compartment on the lights and siren unit. • Loosen the screw in the battery compartment door with a Phillips screwdriver. The screw will remain in the door. •...
- Page 18 Hood Tabs Slot • Position the hood over the front of the vehicle body. • Insert the tabs on the hood into the slots in the vehicle body. Lights and Siren Unit Cord Microphone Cord • Align the arrow on the lights and siren unit cord connector with the arrow on the microphone cord connector.
- Page 19 Long Seat Belt Strap T-Loop Fastener • Insert each end of the long seat belt strap through a slot in the center of the seat. Make sure the fasteners face the outer edge of the seat. • Pull each side of the long seat belt strap evenly through the slots.
- Page 20 Sport Bar • Extend the canopy completely around the sport bar. Sport Bar Bracket Ring Tunnel Sport Bar Support • Using safety scissors, remove the sport bar brackets from the plastic connector. Dispose of the plastic connector. • Position the sport bar upright. •...
- Page 21 • Align the tabs on the inside of a light cover with the slots in one of the light housings on the light rack. Make sure the light covers are positioned with the wide spaced tabs at the top. • Push firmly on the light cover to snap it to the light housing.
- Page 22 Assembly...
-
Page 23: Label Decoration
Label Decoration... -
Page 24: Battery Installation
Important Note: Use only a Power Wheels Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed Power Wheels 12 volt charger before ® operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. -
Page 25: Battery Care And Disposal
Battery Installation Hood Hood Latch • Lower the hood and secure the latches. Battery Care and Disposal Disposal • Your Power Wheels ® battery is a sealed lead-acid battery. It must be recycled or disposed of in an environmentally sound manner. •... -
Page 26: Rules For Safe Driving
RIDING HAZARD WARNING Prevent Injuries and Deaths • Direct Adult Supervision Required • Keep Children Within Safe Riding Areas These areas must be: - away from swimming pools and other bodies of water to prevent drownings - generally level to prevent tipovers - away from steps, driveways, roads and alleys. -
Page 27: How To Operate Your Vehicle
Beginner Use - Low Speed Drive As assembled, your vehicle is ready to roll in low speed mph, maximum). It has been pre-set so it will only operate in low speed. After your child has mastered the basic skills of driving and understands the rules for safe driving, it’s time to disconnect the high speed lock-out to allow the vehicle to operate in low or high speed. -
Page 28: Caring For Your Vehicle
How to Operate Your Vehicle Advanced Use - High Speed Drive Disconnecting the High Speed Lock-Out Shifter Lock-Out Screw • Before you disconnect the high speed lock-out, make sure your child knows how to steer, how to start and stop the vehicle and knows the rules for safe driving. When the high speed lock-out is disconnected, the vehicle can be driven forward in low speed (2 maximum) or high speed (5 mph, maximum). -
Page 29: Problems And Solutions Guide
Problems and Solutions Guide IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a problem, please contact Power Wheels toll-free at 1-800-348-0751 between 8 AM and 6 PM (EST) Monday through Friday. Or, contact your local Power Wheels Authorized Service Center list beginning on page 34. -
Page 30: Problems And Solutions Guide
Problems and Solutions Guide Problem Vehicle was running but Loose wire or loose connectors suddenly stopped Tripped thermal fuse Short run time (Less than Undercharged battery 1 - 3 hours per charge) Overcharged battery Battery is old and will not accept full charge Tripped thermal fuse Possible Cause... - Page 31 Problems and Solutions Guide Problem Vehicle runs sluggishly Undercharged battery Battery needs charging Battery is old and will not accept full charge Vehicle is overloaded Driving conditions are too stressful Vehicle runs in low speed, but High speed lock-out not disconnected does not run in high speed (Please Note: The vehicle is designed to operate in low...
- Page 32 Problems and Solutions Guide Problem When the foot pedal is pressed, Loose wire or connector the vehicle won’t run without a push “Dead Spot” on motor Loud clacking or grinding Broken gears noise from a motor-gearbox Lights and siren not working Improperly installed batteries Dead batteries Charger gets warm during use...
-
Page 33: N Statement Of Limited Warranty
Bumper-to-Bumper* Limited Warranty *One year limited warranty from the date of purchase on the Power Wheels ® vehicle. Six month limited warranty on the 12 volt battery. For the original purchaser, this one year limited warranty covers the Power Wheels ®... -
Page 34: Authorized Service Centers
We are continually expanding our Authorized Service Center Network. Please check this listing for the Authorized Service Center nearest you. If there is not one in your area, please call Power Wheels ® ALABAMA BIRMINGHAM - Frigid Appliance Center, 1861 Centerpoint Rd., 35215, (205) 853-3952 BIRMINGHAM - Frigid Appliance Center, 701 Graymont Ave. - Page 35 ILLINOIS CHAMPAIGN - Appliance Parts & Service, 905 Francis, 61821, (217) 355-0220 DECATUR - Rexx Battery of Decatur, 1330 E. Eldorado Street, 62521, (217) 422-0281 DOWNER’S GROVE - Authorized Appl. Svc. Co., 1644 W. Ogden Ave., 60515, (630) 852-1550, (800) 829-1798 JACKSONVILLE- Rexx Battery Specialists, 847 South Main Street, 62650, (217) 245-2713 LINCOLN - Rexx Battery Specialists, 504 Keokuk, 62656,...
- Page 36 MISSOURI GLADSTONE - Mar-Beck Appliance Serv. Co. Inc., 6559 N. Oak Traffic Way, 64118, (816) 436-9191 INDEPENDENCE - Mar-Beck Appliance Service Co. Inc., 4476 South Noland Road, 64055, (816) 478-1889 KANSAS CITY - Mar-Beck Appliance Service Co. Inc., 303 W. 79th Street, 64114, (816) 523-6931 POPLAR BLUFF - Mills Iron &...
- Page 37 TROY - Hoover Hardware #3958, 9 Canton Street, 16947, (717) 297-3445, (800) 251-2156 WILKES-BARRE - Walter Hardware Do-It Center, 57 N. Welles Street, 18702, (717) 823-1406 YORK - Parcel Plus, 2549 E. Market Street, 17402, (717) 757-1875 PUERTO RICO HATILLO - Tropical Parts Service, Carr 130km 8.5 B0. Pajui 00659, (809) 898-6474 MAYAGUEZ - Cardona Appliance Service, 8 San Vicente Sreet, 00680, (809) 832-8366...
- Page 38 Over 400 Authorized Service Centers Fisher-Price and Power Wheels by Fisher-Price are U.S. trademarks of Mattel, Inc. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052 U.S.A. Printed in the U.S.A. If you are missing parts or need assistance,...