Carrier AQUAFORCE 30XA080-500 Installation Instructions Manual page 68

Table 6 — 30XA080-500 Electrical Data, Dual Point (Standard Condenser Fan Motors) (cont)
UNIT VOLTAGE
UNIT
Supplied
V-Hz
30XA
(3 Ph)
Min Max
230-60 207 253
200-60 187 220
080 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
090 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
100 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
110 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
120 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
140 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
160 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
180 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
200 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
220 460-60 414 506
575-60 518 633
380-60 342 418
230-60 207 253
200-60 187 220
240 460-60 414 506
575-60 518 633
380-60 342 418
460-60 414 506
260 575-60 518 633
380-60 342 418
460-60 414 506
280 575-60 518 633
380-60 342 418
460-60 414 506
300 575-60 518 633
380-60 342 418
460-60 414 506
325 575-60 518 633
380-60 342 418
460-60 414 506
350 575-60 518 633
380-60 342 418
460-60 414 506
400 575-60 518 633
380-60 342 418
460-60 414 506
450 575-60 518 633
380-60 342 418
460-60 414 506
500 575-60 518 633
380-60 342 418
LEGEND
ICF — Instantaneous Current Flow
MCA — Minimum Circuit Amps
MOCP — Maximum Overcurrent Protection
WD — Wye-Delta
XL — Across-the-Line
NOTES:
1. Units are suitable for use on electrical systems where voltage supplied to the unit
terminals is not below or above the listed minimum and maximum limits. Maximum
allowable phase imbalance is: voltage, 2%; amps 10%.
2. Cooler heater is wired into the control circuit so it is always operable as long as the
control power supply disconnect is on, even if any safety device is open.
3. For MCA that is less than or equal to 380 amps, 3 conductors are required.
NUMBER
OF
COND
MCA MOCP
FANS
3/3 182.9/227.9 300/350
3/3 201.5/251.2 300/350
3/3 91.4/113.9 150/175
3/3 70.3/ 88.3 110/125
3/3 106.5/133.7 175/200
4/4 199.9/244.9 300/350
4/4 220.0/269.8 350/400
4/4 99.9/122.4 150/175
4/4 76.4/ 94.4 125/125
4/4 116.5/143.8 175/225
4/4 241.0/244.9 400/350
4/4 264.9/269.8 450/400
4/4 120.0/122.4 200/175
4/4 92.5/ 94.4 150/125
4/4 140.2/143.8 225/225
4/4 241.0/286.0 400/450
4/4 264.9/314.7 450/500
4/4 120.0/142.5 200/225
4/4 92.5/110.5 150/175
4/4 140.2/167.5 225/250
4/4 370.0/244.9 600/350
4/4 407.2/269.8 700/400
4/4 185.0/122.4 300/175
4/4 141.9/ 94.4 225/125
4/4 215.1/143.8 350/225
6/4 423.5/286.0 700/450
6/4 465.6/314.7 800/500
6/4 211.3/142.5 350/225
6/4 162.2/110.5 250/175
6/4 246.0/167.5 400/250
6/4 —
6/4 —
6/4 —
6/4 —
6/4 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
6/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
7/6 —
9/6 —
9/6 —
9/6 —
9/7 —
9/7 —
9/7 —
10/6 —
10/6 —
10/6 —
9/9 —
9/9 —
9/9 —
9/9 —
9/9 —
9/9 —
8/12 —
8/12 —
8/12 —
8/14 —
8/14 —
8/14 —
8/14 —
8/14 —
8/14 —
15 HP PUMP, 3450 RPM
ICF
WD
348.0/393.0 1034.0/1079.0
399.5/449.3 1188.5/1238.3
174.0/196.5 517.0/ 539.5
139.6/157.6 413.6/ 431.6
210.5/237.8 625.5/ 652.8
372.0/417.0 1114.0/1159.0
426.5/476.3 1280.5/1330.3
186.0/208.5 557.0/ 579.5
148.6/166.6 445.6/ 463.6
225.5/252.8 674.5/ 701.8
372.0/417.0
426.5/476.3
186.0/208.5 557.0/ 579.5
148.6/166.6 445.6/ 463.6
225.5/252.8 674.5/ 701.8
372.0/417.0
426.5/476.3
186.0/208.5 557.0/ 579.5
148.6/166.6 445.6/ 463.6
225.5/252.8 674.5/ 701.8
632.0/417.0
724.8/476.3
316.0/208.5 948.0/ 579.5
252.4/166.6 758.4/ 463.6
382.8/252.8 1147.8/ 701.8
800.0/417.0
918.8/476.3
400.0/208.5 1208.0/ 579.5
320.4/166.6 966.4/ 463.6
483.8/252.8 1462.8/ 701.8
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
For MCA between 381-760 amps, 6 conductors are required.
For MCA between 761-1140 amps, 9 conductors are required.
For MCA between 1141-1520 amps, 12 conductors are required.
Calculation of conductors required is based on 75 C copper wire.
4. Wiring for main field supply must be rated 75 C minimum. Use copper for all units.
a. Incoming wire size range for the terminal block is no. 4 AWG (American Wire Gage)
to 500 kcmil.
b. Incoming wire size range of non-fused disconnect with MCA up to 599.9 amps is
3/0 to 500 kcmil.
c. Incoming wire size range of non-fused disconnect with MCA from 600 to 799.9 amps
is 1/0 to 500 kcmil.
d. Incoming wire size range of non-fused disconnect with MCA from 800 to 1199.9 amps
is 250 kcmil to 500 kcmil.
5. Data provided circuit 1/circuit 2 where there are two circuits.
68
CONTROL CIRCUIT
Rec Voltage
Fuse 1 PH,
XL
Size 60 Hz
225/300 115
250/300 115
110/150 115
90/110 115
125/175 115
250/300 115
300/350 115
125/150 115
90/110 115
150/175 115
— 300/300 115
— 350/350 115
150/150 115
110/110 115
175/175 115
— 300/350 115
— 350/400 115
150/175 115
110/150 115
175/200 115
— 450/300 115
— 500/350 115
225/150 115
175/110 115
300/175 115
— 600/350 115
— 600/400 115
250/175 115
200/150 115
300/200 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
— — 115
MCA
and
MOCP
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50