Home audio system with 3 cd changer and digital am/fm receiver (40 pages)
Summary of Contents for Emerson MS7630
Page 1
HOME AUDIO SYSTEM with CD PLAYER and CASSETTE RECORDER OWNER'S MANUAL MS7630 Visit our web site at www.emersonradio.com MS7630_011504.p65 15/1/2004, 11:29...
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrow- WARNING: TO REDUCE THE head symbol, within an equi-...
Page 3
If, after reading this manual, you experience any problems with the operation of this product, please refer to the instructions for obtaining service at the end of this manual. Emerson and Emerson retailers are committed to your satisfaction. Once again, thanks for purchasing this Emerson audio product.
IMPORTANT NOTES • Avoid installing this unit in places exposed to direct sunlight or close to heat radiating appliances such as electric heaters, on top of other stereo equipment that radiates too much heat, places lacking ventilation or dusty areas, places subject to constant vibration and/ or humid or moist areas.
PREPARATION FOR USE UNPACKING AND SET UP • Carefully remove the unit from the carton and remove all packing materials from the unit. • Carefully remove any small strips of tape which may have been used to keep the CD and Cassette doors closed during shipment. •...
SPEAKER CONNECTION Connect each speaker to the corresponding speaker terminals on the back panel of the main unit. Make sure that the left speaker is connected to the (L) left pair of speaker terminals and the right speaker to the (R) right pair of speaker terminals. Also make sure that the speaker wires are correctly connected: that the red wires are connected to the red terminals and the black wires to the black terminals.
FRONT PANEL 1.) POWER ‘ On’ Indicator. 2.) CD Track Number Display. 3.) REPEAT Indicator. 4.) CD PLAY/Pause Indicator. 5.) FM ST. Indicator. 6.) Remote Sensor. 7.) CD Door. 8.) CD Door PUSH OPEN Position. 9.) Tuning Dial Scale. 10.) AM Button. 11.) AM ‘...
REMOTE CONTROL (CD Operations Only) 1.) SKIP Button. 2.) SKIP Button. 3.) PLAY/PAUSE Button. 4.) STOP Button. 5.) REPEAT Button 6.) PROG (Program) Button. 7.) Battery Compartment. (Back Cabinet) BATTERY INSTALLATION 1.) Open the battery door on the back of the remote control by pressing the battery door locking tab in the direction of the arrow.
BATTERY REPLACEMENT When the batteries become too weak, the operating distance of the remote control is greatly reduced and you will need to replace the batteries. USING THE REMOTE CONTROL CORRECTLY • Point the remote control at the Remote Sensor. •...
OPERATING INSTRUCTIONS GENERAL CONTROLS Main POWER Switch (Vacation Switch) The MAIN POWER SWITCH is located on the back panel of the main unit. This switch must be ‘ On’ in order to operate the system. It is not necessary to turn the MAIN POWER SWITCH ‘...
LISTENING TO THE RADIO • Make sure that the main POWER switch on the back of unit is set to “ON”. • Make sure that the FM Wire antenna is extended to its full length. 1.) To turn the system ‘ on’ , rotate the POWER ON/OFF-VOLUME control downwards until a ‘...
PLAYING COMPACT DISCS NOTE: Although this portable CD player can read CD-R and CD-RW discs, in addition to normal CDs, the playability of CD-R and CD-RW discs may be effected by the type of software that was used to create the discs, as well as the quality and condition of the blank media you are using.
Skipping Tracks and High Speed Music Search During CD Playback, repeatedly press the SKIP or SKIP buttons to skip to higher or lower number tracks. When the desired track number appears on the display release the buttons and playback will begin on the desired track. To rapidly search forward or back within a track to locate a specific musical passage, depress and hold either the SKIP or SKIP...
PROGRAMMED PLAYBACK This feature allows you to program up to 20 tracks on a disc for playback in any desired order. Note: You cannot program tracks while a disc is playing. If the disc is playing press the STOP button first before beginning the programming steps below: 1.) Press the PROG.
Page 16
6.) After the last track has played the player stops and the display shows the total number of tracks on the disc. However the program sequence remains in the memory and the PROG indicator remains ‘ on. Press the PLAY/PAUSE button to play the programmed sequence again.
PLAYING CASSETTE TAPES 1.) To turn the system ‘ on’ , rotate the POWER ON/OFF-VOLUME control downwards until a ‘ click’ is heard, and set the Volume to a low level. The POWER indicator comes ‘ on’ . 2.) Open the cassette cover by pulling it outwards at the open tab. 3.) Open the cassette door by pressing the 4.) Place a pre-recorded cassette tape into the slots on the inside of the door with the exposed tape facing down and the full reel on the left side.
Page 18
11.) When you are finished listening stop the tape, open the door, remove the tape and close the door. If you are playing a tape and then switch to the Radio or CD function be sure to press the This prevents excess wear and tear on the mechanism. IMPORTANT: Always press the key to shut off the tape motor before opening the cassette...
Page 19
MAKING A TAPE RECORDING This model allows you to make tape recordings directly from the CD player, or the radio. • Refer to “PLAYING COMPACT DISCS” if necessary to operate the CD player. • Refer to “LISTENING TO THE RADIO” if necessary to tune in the station you wish to record from radio.
STEREO HEADPHONE JACK Connect a set of stereo headphones (not included) with a 3.5mm mini plug to the PHONES jack (located at back panel) for private listening without disturbing others. Before putting on the headphones reduce the VOLUME control to a low level, then put the headphones on and gradually increase the VOLUME control to a comfortable listening level.
CARE AND MAINTENANCE ABOUT CASSETTE TAPES Whenever you record on a cassette any previously recorded material is erased as the new material is recorded. To prevent you from accidentally erasing material which you wish to save, blank cassettes are equipped with erase prevention tabs for each side of the tape.
CASSETTE CARE Two common causes of trouble experienced when using cassettes are: 1.) Tape jamming — Leading to uneven speed in playback, and 2.) Tape tangling — Where the tape wraps itself around vital parts of themechanism. To reduce the likelihood of these problems occurring, the following precautions should be observed: •...
HEAD CLEANING The tape heads, pinch roller and capstan require periodic cleaning. This removes particles of the metal oxide coating that wear off the tape and accumulate on these parts and impair performance. Turn off the power, press the key to open the cassette door, and press the Play key.
COMPACT DISC CARE • To remove a disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. • Fingerprints and dust should be carefully wiped off the disc’ s recorded surface with a soft cloth.Unlike conventional records, compact discs have no grooves to collect dust and microscopic debris, so gently wiping with a soft cloth should remove most particles.
Emerson Radio Corp. in the amount of $9.00 (not required by California residents) to cover shipping and handling costs, and enclose a copy of your proof of purchase.
Page 26
EMERSON Part No. : 16-2929 Printed in China 401-01 MS7630_011504.p65 15/1/2004, 10:06...