Hitachi 46W500 Training page 90

DP-3X CHASSIS MAGIC FOCUS "PATTERN SET UP"
NOTE: This instruction should
be applied when a new DCU is
being replaced.
This instruction shows how to set
up the pattern position for Magic
Focus. Each model has a specific
set up pattern position.
Adjustment Preparation:
Receive NTSC RF or Video Sig-
•
nal.
With Power Off, Press and
•
HOLD the SERVICE ONLY
SWITCH the Deflection / Con-
vergence PWB, then press the
Power On/Off at the same time,
until picture appears, then re-
lease both. (Picture may be dis-
played without convergence cor-
rection data. Press the Service
Only button to bring up Internal
Crosshatch.)
Adjustment Procedure:
1. Press the FREEZE key on R/C.
(One additional line appears near
the top and bottom.
NORMAL MODE: 46 INCH SETS
0 1 2
RH 02
00 FC
RV 02 00 07
GH 00
00 FC
GV 06 01 06
BH 04 FE FE
BV FF
08 03
NORMAL MODE: 51 and 57 INCH SETS
1
0 2
RH 0A 02 F6
RV 01
03 07
GH 08 00 F8
GV 01
05 05
BH 0A FE F8
BV 01
07 02
2. Press the
PHOTO key on DP-37 or
AV Net key on DP-37C / D
DVD key on DP-33W
The PATTERN mode is dis-
•
played as follows.
0
RH : 0A
RV : 03
7
6
3. Use the 6 Key to rotate Arrow.
Arrow rotates clockwise with
each press on the 6 Key.
4. Use the following Keys to switch
color of patterns.
INFO : GREEN
•
0 : RED
•
ANT : BLUE
•
3 4 5 6
FE 02
FC 00
00 F7 01 FD
FE 00
FE 00
00 F9 00 FA
00 00 FE 02
00 01
FD F8
3 5
4 6
FC F6 02 0A
00 00
F9 FD
FE F8 00 08
00 FF
FB FB
FE F8 FE 0A
00 FF
FD FA
5. Press the Thumb Stick Left and
1 2
6. Set the Data Values as shown in
7. Press the PIP MODE (MODE
3
5 4
8. Press the MUTE button 3 times
9. Press the SERVICE ONLY
10.Power set off.
NORMAL MODE: 65 INCH SETS
7
0 1
00
RH 02
08
00
RV 04 02
00
GH 08 00
00 GV 01
03
02
BH 08 FE
00
BV 01
05
7
02
00
02
00
04
00
Right buttons to change the Pat-
tern Position Data in horizontal
Direction. Press the Thumb Stick
Up and Down buttons to change
the Pattern Position Data in Ver-
tical Direction.
the Table below.
on DP-33W) key 2 times to write
the changed data into EEPROM.
First press, ADJ PARAME-
•
TER ? ROM WRITE ? Is dis-
played for alarm.
2nd press writes data into
•
EEPROM. Green dots appear
after completion of operation.
exit Pattern Mode.
SWITCH to exit DCAM.
2 3 4 5
FE 02
F6 F6
06 00 FB FF
F8 00 F8 00
00 FF
04 FC
F8 FE F8 FE
00 FF
02 FD
PAGE 07-06
6 7
00
08
FE 00
08 00
00
FE
08 00
00
FC