Carrier Cavius 9001 Quick Start Manual

Commercial reference: 9001
Developed by CAVIUS
PLEASE READ THE USER GUIDE C A R E -
F U L LY B E F O R E U S E A N D RETAIN FOR
FUTURE USE!
GENERAL DESCRIPTION
The Smart Remote is designed to alert with a
rapid flashing warning light when alarming and to
remotely control the CAVIUS Wireless Alarm Fam-
ily. The torch function can be used to find escape
routes at night.
End cap for battery access
Side button for flashlight
Flashlight
Magnet holder
Learn mode switch
End button for test/hush
SAFETY INSTRUCTIONS
Batteries are to be handled with care and battery
powered devices should be kept out of reach of chil-
dren. Do not try to recharge or burn the batteries.
TECHNICAL INFORMATION
The Smart Remote can be used with the alarms from
the CAVIUS Wireless Alarm Family: Smoke, Heat,
Flood and Mains Power alarms. The maximum
number of alarms that can be interlinked with is 32.
The minimum range is 100m in open field. RF condi-
tions also depend on the house layout and materials.
You should always test it after installation and after
changing batteries.
Diameter: 27mm. Length: 140mm.
The Smart Remote is powered by 3 replaceable AAA
batteries.
Complies to standards: RoHS, REACH, EN60065.
1. HOW TO CONNECT TO THE WIRELESS
ALARM FAMILY:
UK
Open the battery compartment by pressing the
snap. Insert the batteries in the battery compart-
ment respecting polarities.
Normal Mode
Slide the learn switch to the "Learn mode" posi-
tion. The Smart Remote will go into Learn mode.
All alarms that need to be connected to the
Smart Remote in the house should be put into
"Learn mode" by sliding the switch of each device
on the "Learn mode" position.
The flashlight will light up to indicate that "Learn
mode" has been selected.
Please note: Do not take out the batteries during
"Learn mode" as this will interrupt the learn process.
Press and hold the test button on an alarm, of
your own choice, until it beeps and the LED
flashes. This alarm will become the master and
will start sending out a specific house code to
the other alarms.
As the other alarms receive the specific house
code, they will also start flashing their red LED's.
When the red LED light flashes on all alarms,
they are connected and MUST BE SWITCHED
OUT OF 'LEARN MODE' and installed.
Label the original "Learn" alarm in order to easily
add new CAVIUS Wireless Family alarms to the
system.
2. INSTALLATION:
The body of the Smart Remote has a built-in magnet,
so it can be installed on a metal plate mounted on
the wall, or on a fridge or other metal surfaces.
The accompanying metal plate can be installed by
the double sided tape or the enclosed screw set.
Learn Mode
The end cap has a hole in which a lanyard can
be added so the remote can hang from a hook
etc.
3. TEST FUNCTION:
After installation, and at least once per quarter,
test all your alarms by pressing the test button on
the remote to ensure they are operating correctly
and are within range of each other.
It is recommended to check visually every week
if the LED flashes correctly on the alarm (every
48sec.).
Hold the red end button for two swipes of alarms
until the remote stops flashing, sounding and vi-
brating.
The remote is now transmitting a test signal to
your alarms. During the test, the Smart Remote will
flash and sound.
If the Smart Remote is receiving a test signal from
another device, it will also flash and sound to
indicate that it is part of the group. Indication can
be stopped by pressing the end button.
Please note: To ensure an optimal operation in nor-
mal conditions, test function sends out a reduced
power RF signal.
4. ALARM MODE:
When one of the connected alarms is going into
alarm and sending out the RF alarm signal, the
Smart Remote's flashlight will start flashing rapidly
(stroboscope).
The Smart remote has a built in vibrator and
sounder which will follow the sound pattern of
the originating alarm. During the alarm, both the
sounder and vibrator will be activated.
The torch can be switched from stroboscopic flash-
ing to constant on by pressing the side button.
Please note: Flashlight will flash at 2 Hertz (2
times each second) to avoid photo sensitive
epilepsy to be triggered.
The CAVIUS Wireless Family has two different
alarm signals:
Alarm signal 1 (--- --- ---) is life threatening
alarms, like a smoke alarm.
Alarm signal 2 (- - -) is a non life threatening
alarm, like a flooding alarm:
Smoke alarm signal:
Heat alarm signal:
Flood alarm signal:
Please note that only the originating alarm's LED
will flash, so it can be identified.
--- --- ---
--- --- ---
- - -