Roland E-60 Owner's Manual page 133

All manuals and user guides at all-guides.com
G BEAT (1~[number of beats per bar])—Specifies the
beat position. The number of available beats depends on
the time signature in the selected area.
G CPT (1~119)—Refers to the last clock that should be
affected by the edit operation. Change this setting only
if your edit operation should not end exactly on the
selected beat.
IEXECUTE
Press this field to confirm your settings and edit the data.
COPY
The COPY function allows you to copy one track to
another or excerpts of one or all tracks to a different
location. The latter is useful if you need to repeat the
chorus several times at the end of the song but do
not feel like recording all those notes.
ISRC TRACK (ALL, 1~16)
Allows you to select the track whose data you wish to copy.
IFROM
G BAR (1~[last measure of the track or song])—Refers to
the first measure to be edited. By default, the FROM
value is set to the beginning of the selected track(s).
G BEAT (1~[number of beats per bar])—Specifies the
beat position. The number of available beats depends on
the time signature in the selected area.
G CPT (1~119)—This is where you specify the CPT position
of the beginning of the track excerpt to be copied.
Unless you do not need all notes of the first bar, you
should keep the default setting.
ITO
By default, the TO position is set to the last event of the
selected track (or the last event of the longest track when
you select "ALL").
G BAR (1~[last measure of the track or song])—This is
where you specify the bar position of the last measure to
be edited.
G BEAT (1~[number of beats per bar])—Specifies the
beat position. The number of available beats depends on
the time signature in the selected area.
G CPT (1~119)—Refers to the last clock that should be
affected by the edit operation. Change this setting only
if your edit operation should not end exactly on the
selected beat.
ICOPY MODE (Replace, Mix)
Allows you to specify how the data should be copied:
E-60/E-50 Music Workstation
G REPLACE—The selected FROM/TO range overwrites the
data (of the destination track) in the area to which the
selected data are copied.
Copy From 2.1.0 To 3.1.0 Into 4.1.0 SRC TRACK= 1/DST TRACK= 1
REPLACE
MIX
G MIX—The data in the selected range of the source track
are added to the data on the destination track.
In most instances, "REPLACE" is probably a good choice
when you set DATA TYPE to "ALL" or when you wish to
substitute a given "message cluster" (modulation data,
for example) for other messages of the same type (thus
creating a perfect reproduction of a given control
effect).
"MIX", on the other hand, may be useful for adding data
to a number of beats or bars that were not there before,
while keeping the original notes in those places. You can
choose the kind of data to be copied using "DATA TYPE".
Note: The E-60/E-50 has no Undo function. Saving your
song before copying will allow you to load the previous ver-
sion if something goes wrong.
ICOPY TIMES (1~999)
Sets the number of copies you wish to make. The value "3"
means that you will end up with 3 contiguous copies.
IDATA TYPE
Allows you to select the data to be copied:
ALL All parameters listed below.
Note Only note messages.
P.Bender Pitch Bend data.
Control Control change messages.
Change
Prog. C Program change messages.
NRPN Non-registered-parameter-number messages.
These are parameter control functions of the GS/
GM2 format that are easier to use than SysEx
messages (but basically have the same function).
RPN Registered-parameter-number messages. They
work like NRPN messages, and are understood by
many GM- and GM2-compatible tone genera-
tors.
CAF Channel Aftertouch messages.
When you select "Note", a FROM NOTE and TO NOTE field
appear that allow you to set the upper and lower limit of
the notes to be copied. (See also "Fine-tuning the setting
range" on p. 132.)
IDST TRACK
This is where you select the track to which you want to
copy the selected data. If you set SRC TRACK to "ALL", the
DST TRACK setting cannot be changed.
r
Editing 16-track songs
133