Toshiba 19DV616DG Service Manual page 7

Remote Control
Install the batteries
Use batteries type UM4/R03 (AAA-Size).
Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such
batteries. Replace exhausted batteries with new ones. Never try to recharge normal batteries - this could
cause an explosion.
Note:
Exhausted batteries can leak corrosive electrolyte, which may cause damage to the remote control -
therefore remove exhausted batteries immediately.
1 Open the battery 2 Install the batteries as shown
compartment. below, ensuring the correct
polarity.
Distance of Remote Control Operation
Remote sensor
Maximum distance approx. 5m
Transmitter window
The remote control handset will not work properly in the following cases:
If bright sunlight directly beams onto the unit front.
If the batteries have not been installed according to
their polarities.
8
52R0131A_ENG.indd 8
Auto setup
Your unit has an Automatic Preparation:
installation which makes installation Press
in your unit easy. When you turn
1
on the unit for the first time, the
Automatic installation routine is
activated. Using this routine, you
can select the on-screen language
and automatically search for and
store all the receivable analogue
and digital (DVB) channels.
The Automatic station presetting
feature is for the set's built-in tuner
only. If you have a device such as
2
a digital decoder (eg. Satellite or
Digital Terrestrial) connected (see
page 55), you would need to tune it
in separately according to its own
instructions.
3
Note:
• To cancel the Auto Tuning, press
EXIT during the process.
• If on the "AUTO INSTALLATION
COUNTRY " screen "UK" is selected,
"Change No." and "Move To" cannot
be used in UK (see page 23).
THE AUTOMATIC TUNING PROCESS
WILL ONLY START BY ITSELF THE
FIRST TIME YOU SWITCH THE SET
ON. HOWEVER YOU CAN RESTART
THIS PROCESS VIA THE MENU
SYSTEM (see page 12 for analogue
channels, and page 20 for digital
channels).
10
52R0131A_ENG.indd 10
3 Close the battery
compartment.
Point the remote control
directly at the remote sensor.
30 30
If an obstacle is placed between the unit and the
handset.
If the batteries are weak.
on the unit.
AUTO INSTALLATION menu will
AUTO INSTALLATION
appear.
Press or to select LANGUAGE,
LANGUAGE ENGLISH
then press ENTER. Press or to
COUNTRY GERMANY
select desired language.
AUTO TUNING
Then press ENTER.
ENGLISH
EXIT : END MENU: RETURN
Press or to select COUNTRY,
then press ENTER. AUTO INSTALLATION
Press or to select your country. LANGUAGE ENGLISH
Then press ENTER. COUNTRY GERMANY
AUTO TUNING
GERMANY
EXIT : END MENU: RETURN
Press or to select AUTO
TUNING, then press ENTER. AUTO INSTALLATION
The confirmation screen will be
LANGUAGE ENGLISH
displayed. Press ENTER to start
COUNTRY GERMANY
automatic tuning.
AUTO TUNING
Your TV will now automatically tune
in all available channels.
Your TV will tune the analogue
AUTO TUNING
channels first, then tune the digital
10 %
channels.
EXIT : END MENU: RETURN
(ANALOGUE)
Note:
• Please be patient - the Auto
Auto Scan DVB-T 16QAM
Tuning process can take
TV :003 Radio
several minutes to complete.
001 BBC ONE 070 BBC Radio 1
002 BBC TWO
007 BBC THREE
When the programme on the
screen stops changing and the Carrier :1
Frequency (kHz) :562000
sound comes on, the search
Searching...
Progress
process is complete. Exit
(DIGITAL)
Note: Before you connect other appliances:
• To avoid potentially damaging your set, make sure all items are switched off and disconnected from the
mains power when you make the connections.
• Arrange the desired connection.
• When you have finished making the connections, reconnect the mains power to the unit and switch it
back on.
Connect your aerial as shown below. Connections to other equipment is explained further on
pages 53~57. If you have problems with reception, consult a specialist of aerial.
Illustration of 19DV615DG/19DV616DG/22DV615DG/22DV616DG
(M)
(A) (B) (C) (D) (E) (F)(G)(H) (I) (J)
(A) Power supply: Connect the supplied power cable to an AC 220-240V/50Hz mains power supply only - do
not attempt to connect it to any other type of supply. Never try to repair a damaged AC power cord with
isolation-tape - this should be repaired by a specialist or rep laced. Do not let your pet loose near the cable.
Animals biting into the cable could receive a fatal electric shock, and could cause a hazard to others.
(B) HEADPHONE jack: Plug headphones with a mini plug (3.5 mm) into this jack.
(C) COMPONENT input: See page 57.
(D) AV2 input: Input for analogue A/V-Signal (Composite or S-Video). See page 56.
(E) Digital audio output: Digital output for CD/DVD & DVB-T (see page 56).
(F) PC MONITOR input (PC): See page 53.
(G) Scart socket (AV1): For the connection of scart cable. See pages 55~56.
(H) PC/HDMI AUDIO input: See pages 53, 54.
(I) HDMI input : See page 54.
(J) Aerial input socket: Connect the outdoor aerial to the aerial input socket as shown.
(K) C.I. slot: The Common Interface allows you to insert CAM (Conditional Access Module) and a suitable
Smart Card to give you access to additional Pay-TV services. (See page 26) Before inserting the
module, make sure to turn off the main power and then insert the module all the way into the slot until it
is flushed with the side panel buttons.
(L) Bracket holes: Fix a wall mounting bracket (not supplied) here.
(M) INPUT cover: When you access the input jacks, remove this cover (except 22DV615DG/22DV616DG).
(N) AV3 input: Input for analogue A/V-Signal (Composite). See page 56.
(O) Scart socket (AV1/AV2): For the connection of scart cable. See pages 55~56.
(P) HDMI1/HDMI2 input : See page 54.
3/13/09 3:21:02 PM 52R0131A_ENG.indd 9
Quick guide for ANALOG MENU operation/Selecting the
Make sure the aerial connection and
power supply are connected as per
the description on previous page.
Preparations:
• Turn on the unit with the
on the unit. The
will light up in green.
To change the unit to standby mode,
press on the remote control.
(Power) indicator will change
from green to red. To turn on the unit
from standby mode, press
remote control again.
In standby mode, you can also turn
the unit on with
on the unit or PAGE
the remote control.
To turn off the unit press
on the unit - to completely switch
it off, disconnect the mains power
supply.
• Press TV/DVD to select the TV mode.
• Press ATV/DTV to select the
analogue TV mode.
:001
Note:
• If no buttons are pressed for more
than approx. 60 seconds, the MENU
disappears automatically.
3/13/09 3:21:04 PM 52R0131A_ENG.indd 11
Aerial connection
Illustration of 26DV615DG
(L)
(L)
(K)
(A) (E) (N) (C) (O)
video input source/On-screen Language Selection
Quick guide for ANALOG MENU operation
Call ANALOG MENU and for example: Select AUTO TUNING.
1
Press INPUT.
Select ATV. Press MENU.
2
button
Press or to select
(Power) indicator
on the
3
Press or to select AUTO
TUNING, then press ENTER to
(Channel) or
enter the AUTO TUNING menu.
/ on
... on the following pages the MENU
button
can be called in the same way as
here.
4
Press EXIT to return to the normal screen.
Selecting the video input source
Press INPUT to view a signal from
another device connected to your TV,
such as a VCR or DVD player. You can
select each input source depending on
which input jacks you used to connect
your devices.
To select the video input source, press
/ . Then press ENTER within 6 seconds.
• You can return to ATV mode by pressing a numbered button
even if you switched to external input mode from DTV mode.
On-screen Language Selection
1
Select LANGUAGE (unless you
have already selected when the set
was first switched on).
Then press ENTER.
2
Press or to select the desired language.
3
Press EXIT to return to the normal screen.
(M)
ANT.
(B)
(K)
ANT.
(H)(F)(P) (J)
9
3/13/09 3:21:03 PM
.
AUTO TUNING
MANUAL TUNING
CH ALLOCATION
LANGUAGE ENGLISH
VERTICAL POSITION 0
AUTO 4:3 DEFAULT
4:3
AUTO TUNING
MANUAL TUNING
CH ALLOCATION
LANGUAGE ENGLISH
VERTICAL POSITION 0
AUTO 4:3 DEFAULT
4:3
INPUT SELECT
ATV
DTV
AV1
AV2
AUTO TUNING
MANUAL TUNING
CH ALLOCATION
LANGUAGE ENGLISH
VERTICAL POSITION 0
AUTO 4:3 DEFAULT
4:3
ENGLISH
11
3/13/09 3:21:05 PM