Table of Contents
Advertisement
Sounding the PANIC Alarm
Triggering the panic alarm trips the
alarm but will not call the monitoring
station unless you arm the system first.
This option can be changed by the
service station. To trigger the panic
alarm:
• Press PANIC on the Security/Home
Automation Remote Control, or press
ARM and DISARM together on the
Keychain Remote. Press DISARM to
cancel the alarm.
Trouble Alarm
If you hear a repetitive trouble alarm
when you try to arm the system there
is a problem and the system does not
arm. You can:
• Correct the Problem - First press
DISARM to stop the trouble alarm.
Then correct the problem. Then arm
the system again.
• Ignore the problem - While the
trouble alarm is sounding, press
BYPASS. The indicator(s) for the
problem zone(s) flash rapidly. Press
ARM to arm the system. The problem
zone(s) is/are not protected but all
other zones are.
22
All manuals and user guides at all-guides.com
To See the Status of Zones
9-16
If there is a problem with zones 9-16,
you do not see a flashing zone light but
will hear a trouble alarm if you try to
arm the system. Press and hold
BYPASS. This bypasses the problem
and lets you see which zone is reporting
a problem. If you do not want to bypass
the problem, correct the problem then
arm the system.
After an Alarm
When you disarm the system after an
intrusion (or 4 minutes after the alarm
trips) the siren turns off and the lights
which were flashing remain on.
The ARMED indicator flashes and the
zone indicator for the violated zone is
on. Press ARM then DISARM on the
Remote Control to turn to off the zone
indicator and flashing ARMED indicator.
Press LIGHT OFF to turn off X10
Modules set to the same House Code
and Unit Code as the Console.
Switching lights on/off from
the console
Press LIGHT ON or LIGHT OFF on the
console to turn on or off X10 Modules
set to A-13 (or other codes on request
from the monitoring station - see page
18).
TURNING LIGHTS ON AND OFF REMOTELY
Keychain Remote Control
(KR10A)
BATTERY
ARM
PANIC
DISARM
LIGHTS
ON
LIGHTS
OFF
Press LIGHT ON or LIGHT OFF on the
Keychain Remote to turn on or off lights
connected to X10 Modules set to the
A-13 (or other codes on request from
the monitoring station - see page 18).
Note: This Button is not an ALL lights
on button.
Home Automation Remote
Control (HR12A)
ON
OFF
1
2
3
4
5
6
7
8
.
.
A
.
O
C
.
M
.
.
E
.
.
1-8
9-16
K
G
I
The Home Automation Remote Control
provides independent control of up to
16 modules which you set to different
Unit Codes. It transmits signals to the
Security Console which retransmits the
signals to modules over your house
wiring. You can even dim and brighten
lights connected to Lamp and Wall
Switch Modules.
The Home Automation Remote does
not require any "installation." Just fit four
AAA alkaline batteries in its battery
compartment and set its House Code
dial to A (or other code on request from
the monitoring station - see page 18).
Note: If you already own a transceiver
module, you will no longer need to use it.
Security/Home Automation
Remote Control (SH624)
PANIC
PANIC
ARM
DIS-
HOME
ARM
ARM
DIS-
AWAY
ARM
SECURITY
LIGHT
ON
OFF
A
BRIGHT
DIM
O
C
M
E
ENTRY
K
G
DELAY
INSTANT
I
The Security/Home Automation Remote
Control combines the features of the
security remote with the features of the
Home Automation Remote. It lets you
arm and disarm the system in HOME
and AWAY modes (see page 21 for
details). It has SECURITY LIGHT ON
and OFF buttons which work like the
LIGHT ON and LIGHT OFF buttons on
the Keychain Remote. It also lets you
control up to four additional X10
Modules and dim and brighten lights too!
23
Advertisement
Table of Contents
