Professional pan/tilt/zoom camera system (21 pages)
Summary of Contents for X10 Monitor Plus DC8700P
Page 1
All manuals and user guides at all-guides.com ™ Monitor Plus Supervised Security System With Digital Central Station Communicator PANIC PANIC DIS- HOME DIS- AWAY SECURITY PANIC UNIT LIGHT AWAY - ARM - HOME ZONES HOUSE BYPASS ZONES 9-16 Lamp Module ON - LIGHTS - OFF BRIGHT MONITOR...
Also, the telephone company can make changes to its lines, equipment, operations, or procedures If necessary, consult your local X10 Dealer for that could affect the operation of this console. The additional suggestions. telephone company notifies you of these changes Your console’s telephone dialer is designed to...
All manuals and user guides at all-guides.com INTRODUCTION SETTING UP THE CONSOLE Your X10 Powerhouse Monitor Plus X10 Home Automation compatible: Choosing a location for the Security System lets you feel secure. Adding X10 Home Automation products console The system includes a security console...
Page 4
All manuals and user guides at all-guides.com INSTALLATION Mounting the Console Note: The telephone company charges to install the necessary jacks. If desired, the Security Console can be wall mounted using the included mounting The USOC number of the jacks to be installed is RJ11C (or RJ11W for a wall plate bracket.
All manuals and user guides at all-guides.com SETTING UP REMOTE CONTROLS SETTING UP DOOR/WINDOW SENSORS Security/Home Automation Key Chain Remote Control Installing Door/Window Initializing Door/Window Remote Control Sensors Sensors 1. Install two AAA alkaline batteries in the battery compartment (batteries We recommend that you purchase This Procedure initializes the Door/ sold separately).
Page 6
All manuals and user guides at all-guides.com 4. Press TEST again. The Console's Testing Door/Window Note: You can use any standard N.C. next unused zone indicator lights type magnet switches. N.C. means Sensors and the Console beeps to indicate Normally Closed. This type of magnetic it has accepted the sensor.
All manuals and user guides at all-guides.com SETTING UP MOTION SENSORS Initializing Motion Sensors 2. Set the INSTALL/RUN switch on the Installing Motion Sensors console to INSTALL (located under the flip-up door). Correct Wrong For optimum performance the Motion Sensor should be placed so that an intruder walks across its path rather than towards it.
All manuals and user guides at all-guides.com SETTING UP REMOTE MODULES All types of Motion Sensors sense To test the alarm Setting up Lamp Modules Setting up Wall Switch motion by detecting a change in Modules 1. Arm the console and wait for about temperature.
Using the POWERHORN with number downloading and verification, UNIT other X10 controllers The other 3 codes are for X10 modules remote configuration and alarm type that turn on and off randomly between confirmation. In a panic situation, you can trip the HOUSE dusk and the set OFF time.
All manuals and user guides at all-guides.com USING THE SYSTEM Calling Customer Service 3. Service Station Number: Number 11. Daylight parameters: Sets dusk Console Zone Indicators for the service station. times for midwinter and midsummer After you have registered your system The console displays the status of the to activate lived-in look lighting 4.
Page 11
All manuals and user guides at all-guides.com Self checking system When armed RUN1 and RUN2 modes DELAY Mode ARM HOME/ARM AWAY are the same, opening a door or window (Security/Home Automation (Security/Home Automation All Door/Window Sensors and Motion trips the alarm. When the system is in Remote Only) Remote only) Sensors report in to the Console every...
Press LIGHT ON or LIGHT OFF on the 9-16 and AWAY modes (see page 21 for console to turn on or off X10 Modules details). It has SECURITY LIGHT ON set to A-13 (or other codes on request The Home Automation Remote Control...
All manuals and user guides at all-guides.com REPLACING BATTERIES Security Remote Controls Door/Window Sensors was NOT flashing, the sensor is logged Console into the next sequential zone (instead For the Keychain Remote use two AAA If any of the Console's zone indicators The console’s backup battery allows the of the same zone it was in).
All manuals and user guides at all-guides.com TROUBLESHOOTING SOLUTION PROBLEM PROBLEM SOLUTION If the system does not arm. • Check that the slide switch under the If you hear a repetitive trouble alarm Check the zone indicators. If a door or SETUP flip door is set to RUN1 or when you try to arm the system, and it window is open, its zone indicator is on.
Page 15
All manuals and user guides at all-guides.com PROBLEM SOLUTION SOLUTION PROBLEM You open a door or window and the If you do not hear a beep from the With the Console in the RUN 2 mode, • Check that the system is armed. Console when you press TEST to install alarm does not trip.
Page 16
All manuals and user guides at all-guides.com PROBLEM SOLUTION Special Notes Outdoor Infrared Motion Sensor The Outdoor Motion Sensor (Model Intercom Systems If the armed indicator is flashing. This indicates that there has been an PR511) will not trigger the Monitor Plus intrusion.
Page 17
PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE.