Table of Contents
Advertisement
Press the
key to enter add/edit/delete mode. The
selected bank number will be displayed under the legend
"BANK", if in VFO mode the bank number will be replaced
by the letter "V V V V V ". Rotate the SUB DIAL to review the pass
channels.
To delete the frequency of a displayed pass channel press
. The pass channel will be deleted and the pass
list will shuffle down to fill the gap created (unless the
last channel is deleted in which case the "- - -" legend will
be displayed to indicate that the channel (and bank) no
longer contains data.
Rotate the SUB DIAL to continue the review / selection
process. To select another bank press the
return to the first menu and repeat the above process for
another bank.
To accept the input and complete the process, press
in either of the two menus.
13-5 Deleting complete banks of pass
frequencies
Sometimes it is convenient to remove the frequency pass
status of all channels in a search bank instead of reviewing
and deleting them one-by-one (as described in section
13-4 of this manual).... especially if you have previously
registered 100 pass frequencies in a bank.
Ensure the AR5000 is in VFO or memory recall mode, if
in doubt press
.
DEL
DEL
DEL
F-PASS" menu, press
F-PASS
F-PASS
To access the "DEL
DEL
F-PASS
F-PASS
then press and hold the
second. Use the
"DEL F-PASS
DEL F-PASS" is displayed.
DEL F-PASS
DEL F-PASS
DEL F-PASS
DEL MEM-CH
DEL SEL-CH
DEL M-PASS
DEL SRCH
DEL
DEL
DEL
F-PASS
F-PASS
F-PASS
DEL
DEL
F-PASS
F-PASS
Use the SUB DIAL to select the bank containing the
frequency pass channels you wish to delete (00 ~ 19 and
"V V V V V "). The legend "* *" displayed under the bank identifier
shows that the bank contains frequency pass channels
which may be deleted, the legend "- -" indicates that the
key for more than one
keys until the legend
<<<
<<<
<<<
<<<
<<<
search bank does not contain any frequency pass
channels.
To delete all frequency pass channels of the selected bank
press
will change to "- -" to indicate that all the pass frequencies
have been deleted.
Press
depending on which one was previously in use.
(14) Real time clock
The AR5000 is equipped with two independent real time
clocks capable of either 12hr or 24hr format displaying
hours, minutes and seconds. Each clock can also display
a three character text comment which is useful for
key to
identification... UTC, EST, JST etc.
When the AR5000 is switched off but power still
connected, the clock is displayed on the LCD (but without
rear illumination).
The real time clocks are maintained by a SUPER
CAPACITOR while power is disconnected from the
receiver, this will maintain the correct time for up to
approximately 50 hours. It will take a while for the capacitor
to charge up so if only connected to power for a few
minutes, the clocks will not be maintained for long. If the
capacitor has depleted causing the clocks to stop,
all display segments will momentarily illuminate during
power-on of the AR5000 and the clocks will start counting
from 00-00-00 hrs.
14-1 Displaying the clock
To display the real time clock, press
AR5000 will continue to monitor while the clock is displayed
making it ideal for log keeping. The SUB DIAL is used to
select CLOCK 1 or CLOCK 2, the selection being
identified by the legend "1 1 1 1 1 " or "2 2 2 2 2 " on the right hand side
of the LCD.
Pressing any key other than
using any control other than the SUB DIAL will result in
removal of the clock from display and return to a
conventional frequency / text readout.
, after about two seconds the "* *" legend
or
to return to SCAN or VFO mode
,
AR5000 OPERATING MANUAL
. The
,
or
PAGE 61
Advertisement
Table of Contents
