Error Messages; On The Unit's Display - Panasonic DMR-EZ485VK Operating Instructions Manual

Error Messages

On the Unit's Display

H , F
(" " stands for a service number.)
RC (" " stands for a number.)
HARD ERR
("HArd" and "Err" are alternately
displayed.)
NO READ
("NO" and "REAd" are alternately
displayed.)
FULL
UNSUPPORT
("UNSUP" and "POrt" are alternately
displayed.)
UNFORMAT
("UNFOr" and "MAt" are alternately
displayed.)
" " is displayed on the unit's
display.
F74
F75
U59
U61
U72
U73
U76
U88
U99
Continued on next page.
 An error has occurred. The number following "H" or "F" depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
( 81, "To restore the unit if it freezes").
 If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
 The remote control and the main unit are using different codes. Change the
code on the remote control.
 If there is no change after turning the unit on and off, consult the dealer
where the unit was purchased.
 The disc is dirty or badly scratched. The unit cannot record, play, or edit.
 The disc may be incompatible or of poor quality.
 You have used a lens cleaner and it has finished operation. Press
[ OPEN/CLOSE] on the main unit to eject the disc.
 Displayed when the unit is started. This is not a malfunction.
 The unit is carrying out its recovery process. You cannot operate the unit
while " " is displayed.
 There are already 16 scheduled recording programs. Delete unnecessary
scheduled recording programs.
 You have inserted a disc the unit cannot play or record on.
 You tried to operate with a non-compatible USB memory.
 You have inserted a new DVD-RW/+RW or a DVD-RAM/DVD-RW
(DVD-Video format) recorded on other equipment.
You can format the disc when the format confirmation screen is displayed.
 This unit is confirming that it is connected with equipment compatible with
HDAVI Control.
 The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
 The HDMI connection could not be authenticated due to an internal data
malfunction. Consult the dealer where the unit was purchased.
 The unit is very warm.
The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears.
Reinstall the unit in an area with adequate ventilation. Do not block the
cooling fan on the rear of the unit.
 There was a power failure or the AC power supply cord was disconnected
while the unit was on. The unit is carrying out its recovery process. This
process restores the unit to normal operation. The unit is not broken. Wait
until the message disappears.
 The HDMI connection acts unusually.
–
The connected equipment is not HDMI compatible.
–
Please use HIGH SPEED HDMI cables that have the HDMI logo (as shown
on the cover).
–
The HDMI cable is damaged.
 HDMI cannot be output because you are connected to a model that does
not support copyright protection.
 There was something unusual detected with the disc while recording,
playing or copying; there was a power failure or the AC power supply cord
was disconnected while the unit was on. The unit is carrying out its recovery
process. This process restores the unit to normal operation. The unit is not
broken. Wait until the message disappears.
 The unit fails to operate properly. Press [/I POWER] on the main unit to switch the
unit to standby. Press [/I POWER] on the main unit again to turn the unit on.
Page
−
−
57
−
75
74, 75,
76
15
−
−
27
74, 75
73
25, 53
−
−
−
−
−
−
−
83
−
79
RQT9056