Installation - Frigidaire GLEH1642DS0 Installation Instructions Manual

2. The laundry center is equipped with a three-prong
(grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the grounding
prong from the plug.
ELECTRICAL CONNECTIONS FOR A
3-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the
terminal block access cover to the
rear panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the
back panel.
3. Insert a NEMA 10-30 Type SRDT,
U.L. approved power cord through
the strain relief.
4. Attach the power cord neutral (central wire) conductor to
the silver colored center terminal on the terminal block.
Tighten the screw securely.
5. Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal
block.Tighten both screw securely.
6. Tighten the screws securing the cord restraint against
the power cord.
7. Reinstall the terminal access cover.
ELECTRICAL CONNECTIONS
FOR A 4-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the
terminal block access cover to the
rear panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the
back panel.
3. Remove the ground wire
from the green ground screw located above the termial
block.
4. Insert a NEMA 14-30 Type ST or SRDT, U.L. approved
power cord through the strain relief.
5. Attach the green power cord ground wire to the cabinet
with the green ground screw.
6. Attach the white (neutral) wire from the power cord and
the ground wire from the appliance harness to the
silver-colored center terminal on the terminal block.
Tighten the screw securely.
7. Attach the red and black wires from the power cord to
the outer brass-colored terminals on the terminal block.
Tighten both screws securely.
8. Tighten the screws securing the cord restraint firmly
against the power cord.
9. Reinstall the terminal block access cover.

INSTALLATION

1. Run some water from the hot and cold faucets to flush
the water lines and remove particles that might clog up
the water valve screens.
2. Check inlet hoses to ensure the rubber washers are
installed in each end.
3. Carefully connect the inlet hoses to the water valve (on
the left side of the washer cabinet), tighten by hand, then
tighten another 2/3 turn with pliers.
DO NOT CROSS THREAD OR
CAUTION
OVERTIGHTEN THESE CONNECTIONS.
4. Determine which water faucet is the HOT water faucet
and carefully connect the bottom inlet hose to the HOT
water faucet, tighten by hand, then tighten another 2/3
turn with pliers. Carefully connect the top inlet hose to
the COLD water faucet, tighten by hand, then tighten
another 2/3 turn with pliers.
DO NOT CROSS THREAD OR
CAUTION
OVERTIGHTEN THESE CONNECTIONS.
Turn the water on and check for leaks at
both connections.
5. Carefully move the laundry center to its final location.
Rollers on the rear of the washer base allow for easy
movement in closet or alcove installations. Gently push
back on the washer cabinet. NOTE: Gently pushing the
dryer cabinet may lift the front of the washer over 1/8"
which will engage the rear legs to the floor.
6. With the washer in its final position, place a level on top
of the washer, no rocking of the washer should exist.
Adjust the front leveling legs up or down to ensure the
washer is resting solid. Rear leg adjustment is
accessible through the front service panel. Turn the lock
nuts on each leg up towards the base of the washer and
snug with a wrench.
NOTE: Leg extension should not be over one (1) inch to
prevent excessive vibration.
7