Specifications; Installation - JUKI DDL-9000B Instruction Manual

Micro-quantity lubrication
S :
M : Semi-dry
D : Dry

SPECIFICATIONS

Max. sewng speed
Thread trmmng speed
Sttch length
Presser foot lft
(by knee lfter)
Needle *2
Lubrcatng ol JUKI NEW DEFRIX OIL No.  or JUKI MACHINE OIL #7
Nose SS,MS,MA ;
'- Equvalent contnuous emsson sound pressure level (L
A-weghted value of 77 dBA ; (Includes K
SH ;
'- Equvalent contnuous emsson sound pressure level (L
A-weghted value of 77 dBA ; (Includes K
DS ;
'- Equvalent contnuous emsson sound pressure level (L
A-weghted value of 79 dBA ; (Includes K
• The sewing speed will vary depending on the sewing conditions. The sewing speed preset at the time of shipping is 4,000sti/min. The thread trimming
speed can be changed within the range of ( ). The thread trimming speed preset at the time of shipping is 500sti/min.
* 1 : When stitch length exceeds 4 mm or more, set the max. sewing speed to 4,000 sti/min or less for use.
* 2 : Needle used depends on the destination.
* 3 : MA type is for light-weight materials. In the case the sewing machine is used with its speed of stitch set at 4,000 sti/min or higher, the presser
regulating spring and thread tension spring should be changed with S type ones.

1. INSTALLATION

1)
4)
4
1
19.5 mm
23.5 mm
2 3
A B
8)
1) Carry the sewing machine with two persons as shown in the figure above.
(Caution) Do not hold the handwheel.
2) Do not put protrudng artcles such as the screwdrver and the lke at the locaton where the sewng machne s placed.
3) The under cover should rest on the four corners of the machne table groove. Mount rubber hnge seat 8 on the table and fix it on the table with a nail.
4) Fx two rubber seats 1 on sde A (operator's sde) usng nals 2 as llustrated above. Fx two cushon seats 3 on sde B (hnged sde) usng a rubber-based adhesve. Then place
under cover 4 on the fixed seats.
5) Remove ar vent cap 5 attached to the machne bed.
(Caution)
1. If the sewing machine is operated without removing air vent cap 5 , oil leakage from gear box portion C may occur.
2. Be sure to attach cap 5 when transporting the machine head in the state that the machine head is removed from the machine table.
6) Ft knee lfter pressng rod 6 . Ft hnge 7 into the opening in the machine bed, and fit the machine head to table rubber hinge 8 before placng the machne head on cushons 9 on
the four corners.
7) Securely attach head support rod !0 to the table untl t goes no further. Regardng the control panel !1 , remove two side plate fixing screws !2 , place the rubber packng !3 , whch s
one of the accessores of the control panel !1 , between the head secton and control panel !1 , then fix them together.
(Caution)
1. Do not use the screws supplied as accessories of control panel !1 .
2. Be sure to mount the machine head support bar on the machine table so that its height from the table surface becomes 55 to 60 mm. For the sewing machine provided with
the AK device, be sure to mount the support bar on the table so that its height from the table surface becomes 38 to 43 mm.
8) Bundle cable clp band !4 suppled as accessores of the machne head at the root of the cable.
9) Check to be sure that the table and the safety swtch arm !5 are engaged wth each other by 2.0 mm to 3.5 mm, wth the sewng machne slghtly tlted.
(Caution) If the engagement between the table and the safety switch arm is 2 mm or less, Error 302 may occur at the time of startup. Or, if the aforementioned engagement is
3.5 mm or more, safety switch arm !5 may break.
0) If the engagement between the table and safety swtch arm !5 s outsde the range of 2.0 mm and 3.5 mm, loosen safety swtch mountng screw !6 and tlt safety swtch !7 n the
drecton of the arrow to adjust the engagement of safety swtch arm !5 wth the table.
DDL-9000B-
-SS -MS
5,000 st/mn
34 #65 to #0
DP×5 #65 to #0
DB× #9 to #8
DB× #9 to #8
= 2.5 dBA) ; accordng to ISO 082- C.6.2 -ISO 204 GR2 at 4,000 st/mn.
pA
= 2.5 dBA) ; accordng to ISO 082- C.6.2 -ISO 204 GR2 at 4,000 st/mn.
pA
= 2.5 dBA) ; accordng to ISO 082- C.6.2 -ISO 204 GR2 at 4,000 st/mn.
pA
5)
C
5
9)
!4
-DS
4,000 st/mn
500 st/mn (00 to 500st/mn)
5mm *
0 mm (standard) 5 mm (max.)
-
) at the workstaton:
pA
) at the workstaton:
pA
) at the workstaton:
pA
2)
6)
6
9
2.0 to 3.5 mm
!5
–  –
S : Medium-weight materials
H : Heavy-weight materials
A : Light weight materials
-SH
4,500 st/mn
34 #25 to #60
DP×5 #25 to #60
DB× #20 to #23
DB× #20 to #23
JUKI NEW DEFRIX OIL No.  or JUKI MACHINE OIL #7
3)
3
1
6),7)
!1
!2
4
!0
7
10)
!6
-MA
*3
5,000 st/mn
4mm
34 #60 to #75
DP×5 #60 to #75
DB× SAN0 #8 to #
DB× SF #8 to #
8
3
1
!1
!3
!2
!2
7
8
!7