Page 1
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. BUILT TO LAST Thank you for purchasing a Campbell Hausfeld product. If you have any technical questions about this product, please call 1-800-626-4401. For Parts and Accessories: 1-800-626-4401 NOTE: If you purchased Model HV2105, please refer to page 8 for additional instructions on the setup and operation of your product.
• Risk of fire or explosion! Solvent and paint fumes can explode or ignite, causing severe injury and property damage. HV2100, HV2105 • Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively with aluminum. DO NOT USE HALOGENATED HYDROCARBONS WITH THIS EQUIPMENT.
2. Use this position when spraying from top to bottom. 3. Use this position for spotting small objects, corners and sharp angles. Figure 2 - Material flow knob positions and spray patterns HV2100, HV2105 turbine in a warm environment or in direct sunlight.
Thinned latex paint, multi-spec, solvent A.5221 adhesives, wax based paint strippers Table 3 - Needle, Nozzle, and Air Cap Combinations HV2100, HV2105 a connected wet film. Achieving a smooth, level surface will depend on the proper relationship between available atomizing pressure, the viscosity of the coating being applied and the properties of the coating.
Use from can 50-60% 10-30% 20-30% 0-10% 10-40% HV2100, HV2105 spray gun closer or further away from your work piece. A little practice will enable you to master this technique. PRACTICE: Practice using your spray gun by following these steps: 1.
This will ensure an even application of coating. Always release the trigger at the end of a pass. Figure 3 - Proper Spray Technique HV2100, HV2105 Continue spraying in the opposite direction overlapping your previous coat by 1/3 to 1/2. When finished, you should have an even wet coat on your work.
3/8” black lined fluid hose, bag of nuts and bolts for assembly, and instructions. HV2100, HV2105 NOTE: Do not place pressure pot onto the cart or insert handle into cart base until the turbine unit is firmly bolted and secured to the cart.
3. Secure each wing nut into place using a cross pattern, rotating an even amount of pressure on each one until each is tight and secure. HV2100, HV2105 4. Plug the power cord into a proper grounded receptacle outlet. If you are using an...
Store equipment for future application. HV2100, HV2105 Maintenance TURBINE MAINTENANCE The turbine unit needs very little maintenance. The motor has sealed bearings that are pre-lubricated. No service is necessary.
Page 11
Lubricate all threads to ensure smooth operation. Blockages and or leaks may occur if the gun is left on its side or turned upside down. Always hang the gun by the hook when not in use. HV2100, HV2105 www.chpower.com...
1. Move spray gun closer to work piece. 2. Decrease the amount of spray material flowing through spray gun. 3. Reduce air power (use optional air control/texturing device). 4. Use a smaller tip/needle assembly instead of the current one you are using. Thin coating more. HV2100, HV2105...
Male Quick Connect for Turbine Part No. PM068020AV Address parts correspondence to: Campbell Hausfeld 100 Production Drive Harrison, OH 45030 U.S.A. 2-1/2 Gallon (10L) Cart and Fluid Feed System Part No. HV210510AV 25’ Air Hose Part No. HV0126 HV2100, HV2105 www.chpower.com...
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY: A. Provide dated proof of purchase and maintenance records. B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if any, must be borne by the purchaser.