Milnor 30015V7J Service Manual
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washers
  5. 30015V7J
  6. Service manual

Milnor 30015V7J Service Manual

30015 series; 30022 series
Hide thumbs Also See for 30015V7J:
Table of Contents

Advertisement

Quick Links

Published Manual Number/ECN: MAP30C4EBE/2016293A
• Publishing System: TPAS2
• Access date: 07/12/2016
• Document ECNs: Latest
Service
30015/30022
C4E
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Milnor 30015V7J

Summary of Contents for Milnor 30015V7J

  • Page 1 Published Manual Number/ECN: MAP30C4EBE/2016293A • Publishing System: TPAS2 • Access date: 07/12/2016 • Document ECNs: Latest Service 30015/30022 PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

  • Page 3: Table Of Contents

    BMP020053/2002446V Clutch Brake - 30010, 30015CGE; 30015, 30022C4E BMP020054/2011352B 3. Bearing Assemblies Cylinder, Shell, Bearing and Console Installation - 30015V7J, T5E, T5X and 30022V6J, T5J, T5E, T5X BMP100002/2010506B Main Bearing Assembly - 30015C4E, T5E, T5X, V7J and 30022C4E, T5E, T5X, V6J BMP100033/2010506B 4.
  • Page 4 Table of Contents, continued MAP30C4EBE/16293A Page Description Document Drain Installation - 30015V7J, T5E, T5X, C4E, CGE; 30022V6J, T5E, T5X, C4E BMP110057/2011413B 3 Inch Electric Drain Valve BMP920017/2014155A...

  • Page 5: Limited Standard Warranty

    (unless the time period is specifically extended for certain parts pursuant to a specific MILNOR published extended warranty) from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators.

  • Page 6: How To Get The Necessary Repair Components

    • If the component is an electrical component, give the schematic number if known. • If the component is a motor or an electrical control, give the nameplate data from the used component. To write to the Milnor factory: Pellerin Milnor Corporation Post Office Box 400...

  • Page 7: Trademarks Of Pellerin Milnor Corporation

    Trademarks of Pellerin Milnor Corporation BIUUUD14 (Published) Book specs- Dates: 20140821 / 20140821 / 20140821 Lang: ENG01 Applic: UUU Trademarks of Pellerin Milnor Corporation These words are trademarks of Pellerin Milnor Corporation: Table 1: Trademarks AutoSpot™ E-P Plus® Linear Costa Master™ MilTouch™...

  • Page 10: About The Forces Transmitted By Milnor® Washer-Extractors

    • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model and ® size upon request. Floor or foundation sizes shown on any Milnor...
  • Page 11 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain written ® confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
  • Page 12 Paper tags on the machine provide installation guidelines and precautions. The tags can be tie-on or adhesive. You can remove tie-on tags and white, adhesive tags after installation. Yellow adhesive tags must remain on the machine. PELLERIN MILNOR CORPORATION...
  • Page 13 Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, servicing, and commissioning this machine are also available from the Milnor Parts department.
  • Page 14 B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Otherwise, you may twist components, such as valves, damaging them. — End of BIUUUI02 — PELLERIN MILNOR CORPORATION...
  • Page 16 BMP030012/2003202V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Safety Placard Placement Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 17: Avoiding Damage From Allied Remote Chemical Delivery Systems

    ® of such systems by the chemical supply company. Milnor washer-extractors and CBW batch washers (tunnels) are available with convenient inlets for such systems (see Figure 1). Most common of the types of systems currently used in commercial laundering operations are pumped chemical systems.
  • Page 18 CAUTION 1 : Equipment and Textile Damage Hazards—Chemicals leaked into the machine, particularly when it is idle can destroy machine components and textiles left in the machine. Pellerin Milnor Corporation accepts absolutely no responsibility for damage to its equipment or to textiles therein from abnormal contact with chemicals.
  • Page 19 Hence, any concentrated chemical that remains in the injection line between the pump and the machine is free to flow into the machine. Some examples of this are shown in Figure 3. PELLERIN MILNOR CORPORATION...
  • Page 20 PELLERIN MILNOR CORPORATION...
  • Page 21 CAUTION 2 : Injury and Damage Hazards—Chemicals leaking from a chemical system may be corrosive or toxic. Such chemicals can injure personnel and damage equipment. • Use care when connecting chemical lines. • Inspect regularly for leaks. — End of BIWUUI03 — PELLERIN MILNOR CORPORATION...

  • Page 23: 19 1. Service And Maintenance

    Service and Maintenance...

  • Page 24: Fastener Torque Requirements

    If fastener torque specifications or threadlocking compound requirements in an assembly document vary from the specifications in this document, use the assembly document. Figure 1: Common Bolts Used in Milnor Equipment Bolt Head Identifying Marks Legend SAE Grades 1 and 2, ASTM A307, and stainless steel...
  • Page 25 Table 3: Torque Values for Plated Fasteners 5/16-inch and Smaller Bolt Grade Grade 2 Grade 5 Grade 8 Grade BC Bolt Size Pound-Inches Pound-Inches Pound-Inches Pound-Inches 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 26 With Threadlocking Compound 1.1.2. Table 5: Threadlocking Compound Selection by Bolt Size Bolt Size LocTite Product 1/4" 1/4" – 5/8" 5/8" – 7/8" 1" + LocTite 222 LocTite 242 LocTite 262 LocTite 272 High temperature LocTite 277 PELLERIN MILNOR CORPORATION...
  • Page 27 Table 8: Torque Values for Applications of LocTite 262 Bolt Grade Grade 2 Grade 5 Grade 8 Grade BC Bolt Size Pound-feet Pound-feet Pound-feet Pound-feet 3/4 x 10 3/4 x 16 7/8 x 9 7/8 x 14 PELLERIN MILNOR CORPORATION...
  • Page 28 Table 11: Torque Values for Stainless Steel Fasteners 5/16-inch and Smaller 18-8 Stainless with 316 Stainless 18-8 Stainless Loctite 767 Nominal Pound- Pound- Pound- Bolt Size Inches Inches Inches 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 29 CAUTION 2 : Malfunction Hazard—Improper application of threadlocking compounds may result in fasteners becoming loose from impact, heat, or vibration. Loose fasteners can cause the equipment to malfunction. • Read and follow the threadlocking compound manufacturer's instructions and warnings. PELLERIN MILNOR CORPORATION...
  • Page 30 No threadlocking compound here Cover this area Nut depth Disassembly —For low-strength and medium-strength products, disassemble with hand tools. 3.3. For high-strength products, apply localized heat for five minutes. Disassemble with hand tools while the parts are still hot. PELLERIN MILNOR CORPORATION...
  • Page 31 Fastener Torque Requirements Figure 4: Disassembly Use Localized Heat Legend Soldering gun heating small fastener Torch heating large fastener — End of BIUUUM04 — PELLERIN MILNOR CORPORATION...

  • Page 33: Drive Assemblies

    Drive Assemblies...

  • Page 36: Motor Mount

    BMP020053/2002446V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Motor Mount Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 39: Bearing Assemblies

    Bearing Assemblies...
  • Page 43 BMP100002/2010506B (Sheet 4 of 4) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Document Name Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 47: Shell And Door Assemblies

    Shell and Door Assemblies...

  • Page 51: Door Assembly

    BMP020002/2008233B (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Door Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 55 BMP020058/2009442B (Sheet 4 of 4) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List, cont.—Interlock Assembly Description Item Part Number Comments Used In 15U060 FLAT WASHER#6 ANSI TYPEB BRASS 09K062B71 SOLENOID 240/60--220/50 = ILOC...

  • Page 57: Control And Sensing

    Control and Sensing...

  • Page 59: Switch Panel Assembly

    BMP020068/2004055V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Switch Panel Assembly Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 61: Coin Acceptor And Vault

    BMP020061/2003276V (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Coin Acceptor and Vault Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 62: Vibration Safety Switch Adjustments

    Ê A djustments ® When the machine leaves Milnor , the actuator arm is tie-wrapped to prevent damage (except on 30015, 30020, and 30022 models). This tie wrap must be removed after the machine is set into position but before the machine is op- erated.
  • Page 63 that it has reset. In the released position the arm should rest lightly but definitely against the stop on the micro-switch case that prevents any further arm movement to the left. For machines with rigid mounted shells, where the machine is bolted to a very substantial foundation, very little machine movement will occur for a given degree of out-of-balance.

  • Page 65: 61 6. Chemical Supply

    Chemical Supply...

  • Page 67: Water And Drain

    Water and Drain...
  • Page 75 BMP110057/2011413B (Sheet 2 of 2) Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 Parts List—Drain Installation Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 76 DRINVAL 3"N/O MTRDR240V 50/60C 96D350B71 DRINVAL 3"N/C MTRDR240V 50/60 ----------------------------------------------------------------------------COMPONENTS------------------------------------------------------------- 96D35MTR37 120V 50/60CMTR FOR 3"DRAINVAL 96D35MTR71 240V 50/60CMTR FOR 3"DRAINVAL 96D35B0D B0DY & BALL FOR 3" DRAIN VALVE 96D35C0V MTRCOVER 2-PCFOR 3"DRAINVAL 96D35PIN DRIVE PIN KIT FOR 3" DRAIN VAL PELLERIN MILNOR CORPORATION...

This manual is also suitable for:

30015t5e30015t5x30015c4e30015cge30022v6j30022t5e ... Show all

Table of Contents