Omron EJ1 User Manual page 220

Parameter List
Variable Category Add-
type ress
D5 (95) Can be 0100 Input Digital Filter - CH1
changed
0101 Input Value 1 for Input Correction - CH1
during
operation.
0102 Input Shift 1 - CH1
0103 Input Value 2 for Input Correction - CH1
0104 Input Shift 2 - CH1
0105 MV at PV Error - CH1
Standard Control:
Heating and Cooling Control:
0106 MV at Stop - CH1
Standard Control:
Heating and Cooling Control:
Not used.
0109 MV Upper Limit - CH1
Standard Control:
Heating and Cooling Control:
010A MV Lower Limit - CH1
Standard Control:
Heating and Cooling Control:
010B Hysteresis (Heating) - CH1
010C Hysteresis (Cooling) - CH1
010D Alpha - CH1
010E Manual MV - CH1
Standard Control:
Heating and Cooling Control:
010F SP Upper Limit - CH1
0110 SP Lower Limit - CH1
0111 Disturbance Gain - CH1
0112 Disturbance Time Constant - CH1
0113 Disturbance Rectification Band - CH1
0114 Disturbance Judgment Width - CH1
Not used.
0200 Input Digital Filter - CH2
0300 Input Digital Filter - CH3
0400 Input Digital Filter - CH4
Note The decimal point position is determined by the sensor selection. With analog inputs, the decimal point
position is determined by the Decimal Point Position parameter setting. In this case, however, the 0 (****)
decimal point position setting will be treated as a setting of 1 (***.*).
Variable Category Add-
type ress
D6 (96) Can be 0100 Heater Burnout 1 Detection
changed
0101 HS Alarm 1
during
operation.
0102 Heater Overcurrent 1 Detection
Not used.
0200 Heater Burnout 2 Detection
Variable Category Add-
type ress
D7 (97) Can be 0004 Programless Upload Settings 4
changed
0005 Programless Upload Settings 5
during
operation.
0006 Programless Upload Settings 6
012F Programless Upload Settings 303
Parameter name
H' 00000000 to H' 0000270F (0.0 to 999.9)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFFFCE to H' 0000041A (−5.0 to 105.0)
H' FFFFFBE6 to H' 0000041A (−105.0 to 105.0)
H' FFFFFFCE to H' 0000041A (−5.0 to 105.0)
H' FFFFFBE6 to H' 0000041A (−105.0 to 105.0)
H' FFFFFFCE to H' 0000041A (−5.0 to 105.0)
H' 00000000 to H' 0000041A (−0.0 to 105.0)
H' FFFFFFCE to H' 0000041A (−5.0 to 105.0)
H' FFFFFBE6 to H' 00000000 (−105.0 to 0.0)
H' 00000001 to H' 0000270F (1 to 9999)
H' 00000001 to H' 0000270F (1 to 9999)
H' 00000000 to H' 00000064 (0.00 to 1.00)
H' FFFFFFCE to H' 0000041A (−5.0 to 105.0)
H' FFFFFBE6 to H' 0000041A (−105.0 to 105.0)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
H' FFFFFF9C to H' 00000064 (−1.00 to 1.00)
H' 00000001 to H' 0000270F (0.01 to 99.99)
H' 00000000 to H' 0000270F (0 to 9999)
H' FFFFF831 to H' 0000270F (−1999 to 9999)
The rest are the same as channel 1.
Parameter name
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
H' 00000000 to H' 000003E8 (0.0 to 100.0)
The rest are the same as from Heater Burnout Detection 1 to Heater Overcurrent Detection 1.
Parameter name
Setting (monitor) range
Setting (monitor) range
Setting (monitor) range
Appendix
Defau- Unit Attribut- Target Unit
lt es
TC4/ HFU
TC2
0.0 Seconds ch ---
0 EU ch ---
0 EU (See ch ---
note.)
1000 EU ch ---
0 EU (See ch ---
note.)
0 % ch ---
0 % ch ---
105.0 % ch ---
−105.0 %
ch ---
10 EU (See ch ---
note.)
10 EU (See ch ---
note.)
0.65 --- ch ---
0 % ch ---
9999 EU ch ---
−1999
EU ch ---
0.65 --- ch ---
1.00 Seconds ch ---
0 EU (See ch ---
note.)
0 EU (See ch ---
note.)
TC4 ---
TC4 ---
Defau- Unit Attribut- Target Unit
lt es
TC4/ HFU
TC2
0.0 A IO TC2 ---
100.0 A IO TC2 ---
100.0 A IO TC2 ---
Defau- Unit Attribut- Target Unit
lt es
TC4/ HFU
TC2
0900 --- NUM ---
0B00 --- NUM ---
00FF --- NUM ---
00FF --- NUM ---
199