Tube Replacement; Specifications - Fender 65 Deluxe Reverb Operating Instructions Manual

A. FUSE - Protects the amplifier from electrical faults.
Replace fuse only with same type and rating as listed
on the fuse holder. If the amplifier repeatedly blows
fuses, take the amplifier to an authorized Fender
Service Center.
B. POWER RATING - Connect the power line cord to a
grounded AC receptacle in accordance with the voltage
and frequency ratings shown on the Rear Panel of your
amplifier.
C. POWER - Push UP to switch ON the amplifier. Push
DOWN to switch OFF the amplifier.
D. STANDBY - Push DOWN to put the amplifier into
STANDBY mode. Push UP to put the amplifier into
normal OPERATING mode. In STANDBY mode power is
supplied to the tube filaments only.
warm-up time when returning the amplifier to
The tube bias and balance adjustments on your '65 Deluxe Reverb are factory adjusted and
should provide years of service before needing attention. If the sound quality of the amp has
degraded noticeably, the tubes, may be worn and some, usually the output tubes, may need
replacement. If you are unsure about the condition of your tubes, take your amplifier to an
authorized Fender Service Center. Replace tubes with Fender
SPECIFICATIONS below). Tube location is printed on the tube label inside the cabinet.
TYPE:
PART NUMBERS:
POWER:
IMPEDANCES:
FUSE TYPE:
SPEAKER COMPLEMENT:
TUBE COMPLEMENT:
DIMENSIONS:
WEIGHT:
`65 Deluxe Reverb – Rear Panel
This eliminates

Tube Replacement

Specifications

PR 239
021-7470-000 (100V, 50/60Hz) JPN
021-7460-000 (230V, 50Hz) EUR
021-7430-000 (240V, 50Hz) AUS
INPUT: 100W (AC line cord)
INPUTS 1: 1MΩ (both channels)
OUTPUT: 8Ω (both speaker jacks combined)
2A, 125V (100-120V versions)
12-inch, 8Ω, Jensen C12K (P/N-057146)
One Fender Special Design 5AR4 (P/N-041400)
Two Fender Special Design 6V6GT's (P/N-023564)
Four Fender Special Design 12AX7A's (P/N-013341)
Two Fender Special Design 12AT7's (P/N-023531)
HEIGHT:
WIDTH:
DEPTH:
Product specifications are subject to change without notice.
E. INTERNAL SPEAKER JACK - Plug-in connection for
the 8Ω internal speaker. A speaker must always be
connected at this jack when the amplifier is ON. A
speaker impedance load of 8Ω should be used to avoid
distortion or damage to the amplifier.
F. EXTERNAL SPEAKER JACK - Plug-in connection for
an external speaker. This jack is wired in parallel with
the INTERNAL SPEAKER JACK {E} and affects the
speaker impedance load.
G. FOOTSWITCH JACK - Plug-in connection for the
FOOTSWITCH which enables ON/OFF switching of the
VIBRATO and REVERB effects. The VIBRATO effect
will not function without the FOOTSWITCH plugged in.
® original equipment only (see
021-7400-000 (120V, 60Hz) US
021-7440-000 (230V, 50Hz) UK
OUTPUT: 22W at 8Ω (speaker jacks)
INPUTS 2: 136kΩ (both channels)
F1A, 250V (230-240V versions)
17-1/2 in (44.5 cm)
24-1/2 in (62.2 cm)
9-1/2 in (24.1 cm)
42 lb (19.1 kg)
7
OPERATING mode after
short breaks and also extends
tube life. The POWER {C}
switch must be ON for the
STANDBY switch to function.